IFM Electronic OPD100 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 39

IFM Electronic OPD100 Скачать руководство пользователя страница 16

16

Complementary outputs transmit the same sensor information with

oppositional logic levels� This means that both an NC and NO switching

output are available at the same time�
OUT1 can e�g� be used for the detection of good parts, OUT2 for the

detection of bad parts�

6.1 Operation with IO-Link master

The unit is compatible with IO-Link master port class A (type A)�

For operation with IO-Link master port class B (type B) observe the

following:
As a standard, the unit is not compatible with master port class B (type B)�

Pin 2 and pin 5 are used for manufacturer-specific functions� That means

that the main supply voltage of the unit and the additional voltage supply

(master port class B on pins 2/5) are not electrically isolated�

With the following configuration the unit can be used with master port class B:
• Connect unit and IO-Link master via 3 wires: Connect pins 1, 3 and 4 of the

unit with the IO-Link master (do not connect pins 2 and 5)�

7 Operating and display elements

1

2

3

4 5

6

1:

1x LED yellow

Switching status OUT1

2:

1 x LED green

Active LED = power

3:

Graphic display

Display of the measured matching value�

«
...
14
15
16
17
18
...
»

Содержание OPD100








































Отзывы:

Нет отзывов