IFM Electronic efector300 SM0510 Скачать руководство пользователя | Manualshive

Страница: 31 / 45

background image

31

UK

10.1 IO-Link
10.1.1 General information

This unit has an IO-Link communication interface which requires an IO-Link-capa-

ble module (IO-Link master) for operation�
The IO-Link interface enables direct access to the process and diagnostic data

and provides the possibility to set the parameters of the unit during operation�
In addition communication is possible via a point-to-point connection with a USB

adapter cable�
You will find more detailed information about IO-Link at www�ifm�com/gb/io-link�

10.1.2 Device-specific information

You will find the IODDs necessary for the configuration of the IO-Link unit and

detailed information about process data structure, diagnostic information and

parameter addresses at www�ifm�com/gb/io-link�

10.1.3 Parameter setting tools

You will find all necessary information about the required IO-Link hardware and

software at www�ifm�com/gb/io-link�

«
...
29
30
31
32
33
...
»

Содержание efector300 SM0510














































Отзывы:

Нет отзывов

Похожие инструкции для efector300 SM0510

Бренд: TaiDoc Страницы: 31

Бренд: Bacharach Страницы: 60

Бренд: Bacharach Страницы: 4

Бренд: Bacharach Страницы: 17

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Бренд: Flytec Страницы: 2

Бренд: Keysight Страницы: 66

Бренд: CA.MI Страницы: 68

Бренд: aci Страницы: 5

Бренд: LEGRAND Страницы: 5

Digital Piano CA750

Бренд: Kawai Страницы: 76

Бренд: Omega Страницы: 100

Бренд: Konica Minolta Страницы: 92

Бренд: Omega Страницы: 13

Бренд: Vaisala Страницы: 11

Бренд: AEMC Страницы: 4

DistanceMaster Compact

Бренд: LaserLiner Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды