IFM Electronic Efector 300 Скачать руководство пользователя страница 29

Страница: 29 / 31

Select parameter

1� Press [Enter] briefly

2� Press [▲] or [▼] until the requested

parameter is displayed

Display the parameter value

3� Press [Enter] briefly

> The currently set value is displayed for

30 s�

By pressing [Enter] briefly several

times, the display switches between

parameter and parameter value�

Switching to the process value display

► Wait for 30 seconds

► Change from the submenu to the main menu, from the main menu to the process value

display with [▲] or [▼].

11.3 Error indications

Warning message

[OL]

Detection zone of volumetric flow or temperature exceeded�

[UL]

Below the detection zone of volumetric flow or temperature�

[Err]

• Unit faulty / malfunction�

• Measured value outside the detection zone�

[C�Loc]

Setting pushbuttons locked, parameter change rejected�

Active IO-Link communication�

[S�Loc]

Setting pushbuttons locked, parameter change rejected�

Unlock using parameter setting software�

[SEnS]

Sensor signal invalid�

• Measuring pipe not sufficiently filled�

• Medium with a too low conductivity�

[IOE�n]

Malfunction� The unit is faulty and must be replaced�

12 Technical data

Technical data and scale drawing at

www.ifm.com → Data sheet search → Article number.

Содержание Efector 300
































Результаты поиска

Содержание Efector 300

Отзывы:

Похожие инструкции для Efector 300

Бренды по названию

Популярные бренды

IFM Electronic Efector 300, Руководство по эксплуатации

Результаты поиска

Содержание Efector 300

Отзывы:

Похожие инструкции для Efector 300

Бренды по названию

Популярные бренды