IFM Electronic Efector 300 Скачать руководство пользователя страница 27

Страница: 27 / 31

10.6.2 Reading the min/max values for the temperature

► Select [HI�T] or [LO�T]

[HI�T] = max� value, [LO�T] = min� value�

Delete memory:

► Select [HI�T] or [LO�T]�

► Press [Enter] briefly�

► Keep [▲] or [▼] pressed.

> [----] is displayed�

► Press [Enter] briefly�

It makes sense to delete the memories as soon as the unit operates under

normal operating conditions for the first time�

10.6.3 Simulation menu

► Select [S�FLW] and set the flow value to be simulated�

► Select [S�TMP] and set the temperature value to be simulated�

► Select [S�Tim] and set the time of the simulation in minutes�

► Select [S�On] and set the function:

-[On]: The simulation starts� The values are simulated for the time set

at [S�Tim]� [SIM] is displayed simultaneously with the process values�

Cancel with [Enter]�

-[OFF]: The simulation is not active�

10.6.4 Resetting all parameters to factory setting

► Select [rES]�

► Press [Enter] briefly�

► Keep [▲] or [▼] pressed.

> [----] is displayed�

► Press [Enter] briefly�

For the factory settings please refer to the end of these instructions → 13.

We recommend taking down your own settings in that table before carrying

out a reset�

10.6.5 Activating the IO-Link communication interface

► Select [IO-L] and set the function:

-[OFF] = IO-Link interface deactivated�

-[On] = IO-Link interface activated�

The analogue output OUT1 is deactivated when the IO-Link

interface is activated�

Содержание Efector 300
































Результаты поиска

Содержание Efector 300

Отзывы:

Бренды по названию

Популярные бренды

IFM Electronic Efector 300, Руководство по эксплуатации

Результаты поиска

Содержание Efector 300

Отзывы:

Бренды по названию

Популярные бренды