manualshive.com logo in svg

IFM Electronic Ax460, Руководство по эксплуатации, Страница: 32 / 36

Поделиться
Скачать
IFM Electronic Ax460 Скачать руководство пользователя страница 32

Operating instructions AX460

32

GREEN

The display is green�

YELLOW

The display is yellow�

10

Minimum display brightness

90

Default value

100

Maximum display brightness

BRIGHTNESS (%)

This parameter defines the display brightness in %�
10

Minimum display brightness

80

Default value

100

Maximum display brightness

CONTRAST

This parameter defines the display's angle of view�
0

Angle of view from above

1

Angle of view from the front

2

Angle of view from below

SCREEN SAVER (S)

This parameter defines the time in seconds after which the display goes off�
0

Display stays on

���
9999

Longest time until the display goes off

UP-DATE-TIME (S)

This parameter defines the display refreshing time in seconds�
0�005

Minimum update time

0�1

Default value

9�999

Maximum update time

FONT

With this parameter, the font of the clear text can be selected�
0

Standard

1

Font 1

10  linearisation

By means of this function a linear input signal can be converted into a non-

linear display (or vice versa)� Up to 24 linearisation points are available for 

input 1 and input 2� They can be distributed across the whole conversion area 

at any distances� There is automatic linear interpolation between 2 predefined 

coordinates�

Содержание Ax460





































Отзывы:

Нет отзывов