IFM Electronic Ax460 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 36

IFM Electronic Ax460 Скачать руководство пользователя страница 16

Operating instructions AX460

16

Menu / parameter

Menu / parameter

COMMAND MENU

DISPLAY MENU

INPUT 1 ACTION

START DISPLAY

INPUT 1 CONFIG

SOURCE SINGLE

INPUT 2 ACTION

SOURCE DUAL TOP

INPUT 2 CONFIG

SOURCE DUAL DOWN

INPUT 3 ACTION

COLOR

INPUT 3 CONFIG

BRIGHTNESS (%)
CONTRAST
SCREEN SAVER (S)
UP-DATE-TIME (S)
FONT

9.2 General Menu

OPERATIONAL MODE

This parameter defines which measuring function (operating mode) the device is supposed to fulfil�
SINGLE

One-channel operation (only input 1)

DUAL

Two-channel operation (input 1 and 2 separately)

IN 1 + IN 2

Two-channel operation of inputs 1 and 2, type of linking: addition�

IN 1 – IN 2

Two-channel operation of inputs 1 and 2, type of linking: subtraction�

IN 1 x IN 2

Two-channel operation of inputs 1 and 2, type of linking: multiplication�

IN 1 / IN 2

Two-channel operation of inputs 1 and 2, type of linking: division�

PIN PRESELECTION

This parameter defines the PIN code for locking the quick-start function to enter the preset values in

the PRESELECTION VALUES menu (emergency PIN: 6079)� Locking the quick start is only useful if all

parameters are locked�
0000

Access not locked

…
9999

Access after entering the PIN code 9999

PIN PARAMETER

This parameter defines the PIN code for the locked access for all parameters (emergency PIN: 6079)�
0000

Access not locked

…

9999

Parameter setting of the device is only possible after entering the PIN

code�

«
...
14
15
16
17
18
...
»

Содержание Ax460





































Отзывы:

Нет отзывов