Ier Automatic Systems BL52 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 56

background image

The information contained in this document is the property of Automatic Systems and is confidential. The recipient shall refrain from using it for any purpose other than the use of the products or the
execution of the project to which it refers, and from communicating it to third parties without Au

tomatic Systems’ prior written agreement. Document subject to change without notice.

BL5x-MT-EN-13

page

19/56

Parameter

Values

Description

Positioning

Definition of the type of sensor used to position the obstacle.

Limit Switches
(by default)

To be selected if the open/close position of the obstacle is
determined by limit switches.

Analog. Sensor

To be selected if the position of the obstacle is determined
by an analogue sensor.

The analogue position sensor measures the distance
separating it from a spiral cam located on the shaft that
transmits the movement of the obstacle’s motor, which
means that the angular position of the obstacle is known at
all times. Also, see the Min Sensor Max parameter below.

Manual Switch

This message is displayed if it is not possible to activate the
analogue sensor, as per one of these cases:



The crank presence detector (only present on some

equipments) is engaged.
=> Remove the crank so that the motor may be engaged.



If the equipment does not have a crank presence

detector, the circuit may have been cut.
=> link the corresponding connections.

Activate Motor?

Pushing the OK key within 5 seconds launches the analogue
sensor activation procedure (see below)

and the movement

of the obstacle!

The Barrier Type and Arm characteristics
must be selected BEFORE initializing the
analogue sensor. Otherwise, rough
movements of the arm can occur with risk

of injury for the personnel and the equipment.

=> Navigate through the menus by means of the upper
key (



).

Search LSO…

The obstacle opens to look
for its open limit position.

The obstacle is moving
during this phase!

Search LSC…

The obstacle closes to look
for its close limit position.

Init. Passed

This is displayed if the open and closed limit values have
been recorded.
The analogue sensor is then operational.

The message disappears after 5 seconds or if the OK key is
pushed.

IMPORTANT

: Save the values in MEM1 or MEM2

(MEMORY menu).

Adjust Sensor

Activation failed because the analogue sensor was not
properly positioned => adjust it (closer or further away from
the cam) so the measurement is included in the working
range (= between the min. and the max. set in the

Min

Sensor

Max

parameter below).

«
...
17
18
19
20
21
...
»

Содержание Automatic Systems BL52

























































Отзывы:

Нет отзывов

Похожие инструкции для Automatic Systems BL52

ServeRAID-MR10is

Бренд: IBM Страницы: 94

ServeRAID-4 Ultra160 Series

Бренд: IBM Страницы: 20

8271 Nways Ethernet LAN Switch

Бренд: IBM Страницы: 6

Бренд: IBM Страницы: 86

Бренд: IBM Страницы: 205

Бренд: IBM Страницы: 28

Бренд: Panamax Страницы: 16

Бренд: Rabbit Страницы: 38

Бренд: Union Instruments Страницы: 63

Бренд: Nice Страницы: 120

Бренд: Radionics Страницы: 18

Century 2 NCL10000 Series

Бренд: BraunAbility Страницы: 39

Бренд: Renogy Страницы: 36

Бренд: EOS Страницы: 7

OBID ID ISC.ANT40/30

Бренд: Feig Electronic Страницы: 2

Бренд: Parker Страницы: 58

Бренд: KATO VISION Страницы: 23

Бренд: CTE Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды