Ier Automatic Systems BL52 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 56

background image

The information contained in this document is the property of Automatic Systems and is confidential. The recipient shall refrain from using it for any purpose other than the use of the products or the
execution of the project to which it refers, and from communicating it to third parties without Au

tomatic Systems’ prior written agreement. Document subject to change without notice.

BL5x-MT-EN-13

page

21/56

Parameter

Values

Description

BL 46 AVR

Parameter to select for a BL46 with automatic opening of the
arm in case of power cut.

Arm Length

Specification of the arm mounted on the barrier; this allows
the program to automatically modify the opening and closing
curves.

If the selected length does not correspond to a standard for
the barrier selected in the Barrier Type parameter, the
message Doesn't Exist appears briefly.

Note

: arm length = free passage = distance between the

arm tip and the barrier housing.

2m00

Select this for a BL4x or BL229 with an arm of 2 m.

2m50

Select this for a BL4x or BL229 with an arm of 2.5 m.

3m00

Select this for a BL4x or BL229 with an arm of 3 m.

3m50

Select this for a BL4x or BL229 with an arm of 3.5 m.

4m00

Select this for a BL4x or BL229 with an arm of 4 m.

4m50

Select this for a BL4x or BL229 with an arm of 4.5 m.

5m00 (by default)

Select this for a BL4x or BL229 with an arm of 5 m.

5m50

Select this for a BL4x or BL229 with an arm of 5.5 m.

6m00

Select this for a BL4x or BL229 with an arm of 6 m.

7m00

Select this for a BL4x with an arm of 6,5 or 7 m.

8m00

Select this for a BL4x with an arm of 7,5 or 8 m.

9m00

Select this for a BL4x with an arm of 8,5 or 9 m.

10m00

Select this for a BL4x with an arm of 9,5 or 10 m.

11m00

Select this for a BL4x with an arm of 10,5 or 11 m.

12m00

Select this for a BL4x with an arm of 11,5 or 12 m.

Non-modifiable

Message displayed when the Barrier Type parameter does
not allow any modification of the arm length.

Incompatible

Message displayed when the selected Arm Length is not
compatible with the selected Barrier Type.

Arm Type

Specification of the type of arm assembled on the barrier.
This parameter only applies to the BL 229 Highway and is
not taken into account for other types of equipment.

Aluminium (default)

Aluminium arm.

Carbon

Carbon arm.

Non-modifiable

Message displayed for the equipments different than BL229
Highway.

Power Fail OP

Choice

(*)

of mode for unlocking the obstacle during a loss of

supply voltage.

(*)

Except for BL4x, where this parameter is automatically set

to ON and not adjustable.

Arm length

«
...
19
20
21
22
23
...
»

Содержание Automatic Systems BL52

























































Отзывы:

Нет отзывов

Похожие инструкции для Automatic Systems BL52

Бренд: Gantner Страницы: 56

Бренд: BADLANDS Страницы: 2

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: Valcom Страницы: 6

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: ACL Страницы: 20

ZoneSense Plus AS

Бренд: Halma Страницы: 58

PARTNER II Release 4.1

Бренд: Lucent Technologies Страницы: 363

Ambience Control 1

Бренд: EuroLite Страницы: 20

Бренд: SKF Страницы: 88

Бренд: Inkel Страницы: 12

Бренд: FMS Страницы: 108

Бренд: Broadcast Tools Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды