IEI Technology PM-BT series Скачать руководство пользователя страница 86

Страница: 86 / 108

PM-BT SBC

Page 74

5.4.2 South Bridge

Use the

South Bridge

menu (

BIOS Menu 17

) to configure the south bridge parameters.

Chipset

Auto Power Button Status

[Disabled (ATX)]

Restore AC Power Loss

[Last State]

> PCI Express Configuration

Audio Configuration

Audio Controller

[Enabled]

XHCI Mode

[Auto]

Select AC power state
when power is re-applied
after a power failure.

---------------------



: Select Screen

↑

↓

: Select Item

Enter:  Select
+/-: Change  Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 17: South Bridge



Restore on AC Power Loss [Last State]

Use the

Restore on AC Power Loss

BIOS option to specify what state the system

returns to if there is a sudden loss of power to the system.



Power Off

The system remains turned off



Power On

The system turns on



Last State

EFAULT

The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.



Audio Controller [Enabled]

Use the

Audio Controller

BIOS option to enable or disable the High Definition Audio

controller.



Disabled

The High Definition Audio controller is disabled.



Enabled

EFAULT

The High Definition Audio controller is enabled.

Содержание PM-BT series













































































































Результаты поиска

Содержание PM-BT series

Отзывы:

Похожие инструкции для PM-BT series

Бренды по названию

Популярные бренды

IEI Technology PM-BT series, Руководство пользователя

Результаты поиска

Содержание PM-BT series

Отзывы:

Похожие инструкции для PM-BT series

Бренды по названию

Популярные бренды