manualshive.com logo in svg

IEI Technology PM-BT series, Руководство пользователя

Поделиться
Скачать
IEI Technology PM-BT series Скачать руководство пользователя страница 81

 

 

PM-BT SBC 

Page 69 

 

Serial-ATA (SATA) [Enabled] 

Use the 

Serial-ATA (SATA)

 option to configure the SATA controller. 

 

Enabled 

D

EFAULT

 

Enables the on-board SATA controller. 

 

Disabled 

 

Disables the on-board SATA controller. 

 

SATA Mode [AHCI Mode] 

Use the 

SATA Mode 

option to configure SATA devices as normal IDE devices. 

 

IDE Mode 

 

Configures SATA devices as normal IDE device. 

 

AHCI Mode 

D

EFAULT

 

Configures SATA devices as AHCI device. 

 

5.3.10 USB Configuration 

Use the 

USB Configuration

  menu (

BIOS Menu 13

) to read USB configuration 

information and configure the USB settings. 

Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. 

 

Advanced 

 

 

 

 

 

 

 

USB Configuration 
 
USB Devices: 
        1 Keyboard, 1 Hub 

 
Legacy USB Support 

[Enabled] 

 
 

 
Enables Legacy USB 
support. AUTO option 
disables legacy support 
if no USB devices are 
connected. DISABLE 
option will keep USB 
devices available only 
for EFI applications. 
--------------------- 



: Select Screen 

↑

 

↓

: Select Item 

Enter:  Select 
+/-:  Change  Opt. 
F1:  General Help 
F2:  Previous Values 
F3:  Optimized Defaults 
F4:  Save & Exit 
ESC: Exit 

Version 2.16.1242. Copyright (C) 2013 American Megatrends, Inc. 

BIOS Menu 13: USB Configuration

 

Содержание PM-BT series













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды