IEI Technology PM-BT series Скачать руководство пользователя страница 53

Страница: 53 / 108

PM-BT SBC

Page 41

WARNING:

The installation instructions described in this manual should be

carefully followed in order to prevent damage to the components and

injury to the user.

Before and during the installation please

the following:



Read the user manual:

The user manual provides a complete description of the PM-BT

installation instructions and configuration options.



Wear an electrostatic discharge cuff (ESD):

Electronic components are easily damaged by ESD. Wearing an ESD cuff

removes ESD from the body and helps prevent ESD damage.



Place the PM-BT on an anti-static pad:

When installing or configuring the motherboard, place it on an anti-static

pad. This helps to prevent potential ESD damage.



Turn all power to the PM-BT off:

When working with the PM-BT, make sure that it is disconnected from all

power supplies and that no electricity is being fed into the system.

Before and during the installation of the PM-BT,

DO NOT:



Remove any of the stickers on the PCB board. These stickers are required for

warranty validation.



Use the product before verifying all the cables and power connectors are

properly connected.



Allow screws to come in contact with the PCB circuit, connector pins, or its

components.

Содержание PM-BT series













































































































Результаты поиска

Содержание PM-BT series

Отзывы:

Похожие инструкции для PM-BT series

Бренды по названию

Популярные бренды

IEI Technology PM-BT series, Руководство пользователя

Результаты поиска

Содержание PM-BT series

Отзывы:

Похожие инструкции для PM-BT series

Бренды по названию

Популярные бренды