IEI Technology NANO-ULT5 Скачать руководство пользователя страница 90

Страница: 90 / 147

NANO-ULT5 SBC

Page 76

5.1 Introduction

The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.

NOTE:

Some of the BIOS options may vary throughout the life cycle of the
product and are subject to change without prior notice.

5.1.1 Starting Setup

The UEFI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.

1. Press the

ELETE

key as soon as the system is turned on or

2. Press the

ELETE

key when the “

Press Del to enter SETUP

” message

appears on the screen.

If the message disappears before the

ELETE

key is pressed, restart the computer

and try again.

5.1.2 Using Setup

Use the arrow keys to highlight items, press

NTER

to select, use the PageUp and

PageDown keys to change entries, press

for help and press

to quit. Navigation

keys are shown in.

Key

Function

Up arrow

Move to previous item

Down arrow

Move to next item

Left arrow

Move to the item on the left hand side

Right arrow

Move to the item on the right hand side

Increase the numeric value or make changes

Содержание NANO-ULT5




















































































































































Результаты поиска

Содержание NANO-ULT5

Отзывы:

Похожие инструкции для NANO-ULT5

Бренды по названию

Популярные бренды

IEI Technology NANO-ULT5, Руководство пользователя

Результаты поиска

Содержание NANO-ULT5

Отзывы:

Похожие инструкции для NANO-ULT5

Бренды по названию

Популярные бренды