IEI Technology NANO-ULT5 Скачать руководство пользователя страница 108

Страница: 108 / 147

NANO-ULT5 SBC

Page 94



Bits per second [115200]

Use the

Bits per second

option to specify the serial port transmission speed. The speed

must match the other side. Long or noisy lines may require lower speeds.



9600

Sets the serial port transmission speed at 9600.



19200

Sets the serial port transmission speed at 19200.



57600

Sets the serial port transmission speed at 57600.



115200

EFAULT

Sets the serial port transmission speed at 115200.



Data Bits [8]

Use the

Data Bits

option to specify the number of data bits.



Sets the data bits at 7.



EFAULT

Sets the data bits at 8.



Parity [None]

Use the

Parity

option to specify the parity bit that can be sent with the data bits for

detecting the transmission errors.



None

EFAULT

No parity bit is sent with the data bits.



Even

The parity bit is 0 if the number of ones in the data
bits is even.



Odd

The parity bit is 0 if the number of ones in the data
bits is odd.



Mark

The parity bit is always 1. This option does not
provide error detection.



Space

The parity bit is always 0. This option does not
provide error detection.

Содержание NANO-ULT5




















































































































































Результаты поиска

Содержание NANO-ULT5

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology NANO-ULT5, Руководство пользователя

Результаты поиска

Содержание NANO-ULT5

Отзывы:

Бренды по названию

Популярные бренды