IEI Technology NANO-ULT5 Скачать руководство пользователя страница 118

Страница: 118 / 147

NANO-ULT5 SBC

Page 104



Power Saving Function(ERP) [Disabled]

Use the

Power Saving Function(ERP)

BIOS option to enable or disable the power

saving function.



Disabled

EFAULT

Power saving function is disabled.



Enabled

Power saving function is enabled. It will reduce power
consumption when the system is off.



USB Power SW [+5V DUAL]

Use the

USB Power SW

BIOS option to configure whether to provide power to the USB

connectors when the system is in S3/S4 sleep state. This option is valid only when the
above

Power Saving Function (ERP)

BIOS option is disabled.



+5V
DUAL

EFAULT

Power is provided to the USB connectors when the
system is in S3/S4 sleep state



+5V

Power is not provided to the USB connectors when the
system is in S3/S4 sleep state



HD Audio [Enabled]

Use the

HD Audio

BIOS option to enable or disable the High Definition Audio controller.



Disabled

The High Definition Audio controller is disabled.



Enabled

EFAULT

The High Definition Audio controller is enabled.

Содержание NANO-ULT5




















































































































































Результаты поиска

Содержание NANO-ULT5

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology NANO-ULT5, Руководство пользователя

Результаты поиска

Содержание NANO-ULT5

Отзывы:

Бренды по названию

Популярные бренды