IEI Technology Nano-PV-D4251 Скачать руководство пользователя

Страница: 87 / 153

NANO-PV-D4251/N4551/D5251 EPIC SBC

Page 74

5.3.4 SATA Configuration

Use the

SATA Configuration

menu (

BIOS Menu 6

) to change and/or set the

configuration of the SATA devices installed in the system.

Advanced

PATA Master

Not Present

PATA Slave

Not Present

SATA Port0

Not Present

SATA Port1

Not Present

SATA Port2

Not Present

SATA Port3

Not Present

ATA/IDE Configuration

[Enhanced]

Configure SATA as

[IDE]

Select ATA/IDE
Configuration.

---------------------

ÅÆ

: Select Screen

↑

↓

: Select Item

Enter

Select

F1 General

Help

F2 Previous

Values

F3 Optimized
Defaults
F4 Save

ESC Exit

BIOS Menu 6: IDE

Configuration

ATA/IDE Configurations [Enhanced]

Use the

ATA/IDE Configurations

option to configure the ATA/IDE controller.

Disabled

Disables the on-board ATA/IDE controller.

Compatible

Configures the on-board ATA/IDE controller to be in

compatible mode. In this mode, a SATA channel will

replace one of the IDE channels. This mode supports

up to 4 storage devices.

Enhanced D

EFAULT

Configures the on-board ATA/IDE controller to be in

Enhanced mode. In this mode, IDE channels and SATA

channels are separated. This mode supports up to 6

storage devices. Some legacy OS do not support this

mode.

Содержание Nano-PV-D4251


























































































































































Результаты поиска

Содержание Nano-PV-D4251

Отзывы:

Похожие инструкции для Nano-PV-D4251

Бренды по названию

Популярные бренды

IEI Technology Nano-PV-D4251, Руководство пользователя

Результаты поиска

Содержание Nano-PV-D4251

Отзывы:

Похожие инструкции для Nano-PV-D4251

Бренды по названию

Популярные бренды