IEI Technology Nano-PV-D4251 Скачать руководство пользователя

Страница: 83 / 153

NANO-PV-D4251/N4551/D5251 EPIC SBC

Page 70

System Time [xx:xx:xx]

Use the

System Time

option to set the system time. Manually enter the hours, minutes

and seconds.

5.3 Advanced

Use the

Advanced

menu (

BIOS Menu 2

) to configure the CPU and peripheral devices

through the following sub-menus:

WARNING!

Setting the wrong values in the sections below may cause the system

to malfunction. Make sure that the settings made are compatible with

the hardware.

Main

Advanced

Chipset

Boot

Security

Save & Exit

> ACPI Settings
> Trusted Computing
> CPU Configuration
> IDE Configuration
> USB Configuration
> Super IO Configuration
> H/M Monitor
> Serial Port Console Redirection

System ACPI Parameters

----------------------

ÅÆ

: Select Screen

↑

↓

: Select Item

Enter

Select

F1 General

Help

F2 Previous

Values

F3 Optimized
Defaults
F4 Save

ESC Exit

BIOS Menu 2: Advanced

5.3.1 ACPI Settings

The

ACPI Settings

menu (

BIOS Menu 3

) configures the Advanced Configuration and

Power Interface (ACPI) options.

Содержание Nano-PV-D4251


























































































































































Результаты поиска

Содержание Nano-PV-D4251

Отзывы:

Похожие инструкции для Nano-PV-D4251

Бренды по названию

Популярные бренды

IEI Technology Nano-PV-D4251, Руководство пользователя

Результаты поиска

Содержание Nano-PV-D4251

Отзывы:

Похожие инструкции для Nano-PV-D4251

Бренды по названию

Популярные бренды