background image

 

 

NANO-PV-D4251/N4551/D5251 EPIC SBC 

Page 131

computer is usually a male DE-9 connector. 

DAC 

The Digital-to-Analog Converter (DAC) converts digital signals to 

analog signals. 

DDR 

Double Data Rate refers to a data bus transferring data on both the 

rising and falling edges of the clock signal. 

DMA 

Direct Memory Access (DMA) enables some peripheral devices to 

bypass the system processor and communicate directly with the 

system memory. 

DIMM 

Dual Inline Memory Modules are a type of RAM that offer a 64-bit data 

bus and have separate electrical contacts on each side of the module. 

EHCI 

The Enhanced Host Controller Interface (EHCI) specification is a 

register-level interface description for USB 2.0 Host Controllers. 

GbE 

Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0 

Gbps and complies with the 

3

IEEE 802.3-2005 standard. 

GPIO 

General purpose input 

IrDA 

Infrared Data Association (IrDA) specify infrared data transmission 

protocols used to enable electronic devices to wirelessly communicate 

with each other. 

L1 Cache 

The Level 1 Cache (L1 Cache) is a small memory cache built into the 

system processor. 

L2 Cache 

The Level 2 Cache (L2 Cache) is an external processor memory cache.

LVDS 

Low-voltage differential signaling (LVDS) is a dual-wire, high-speed 

differential electrical signaling system commonly used to connect LCD 

displays to a computer. 

MAC 

The Media Access Control (MAC) protocol enables several terminals or 

network nodes to communicate in a LAN, or other multipoint networks. 

Содержание Nano-PV-D4251


























































































































































Отзывы: