IEI Technology KINO-690S1 Скачать руководство пользователя страница 91

Страница: 91 / 229

KINO-690S1 Mini-ITX Motherboard

Page 73

5.4 CPU, CPU Cooling Kit and DIMM Installation

WARNING:

A CPU should never be turned on without the specified cooling kit

being installed. If the cooling kit (heat sink and fan) is not properly

installed and the system turned on, permanent damage to the CPU,

KINO-690S1 and other electronic components attached to the system

may be incurred. Running a CPU without a cooling kit may also result

in injury to the user.

The CPU, CPU cooling kit and DIMM are the most critical components of the

KINO-690S1. If one of these components is not installed the KINO-690S1 cannot run.

5.4.1 AMD Socket S1 CPU Installation

WARNING:

CPUs are expensive and sensitive components. When installing the

CPU please be careful not to damage it in anyway. Make sure the CPU

is installed properly and ensure the correct cooling kit is properly

installed.

To install a AMD Socket S1 CPU onto the KINO-690S1, follow the steps below:

WARNING:

When handling the CPU, only hold it on the sides. DO NOT touch the

pins at the bottom of the CPU.

Содержание KINO-690S1






































































































































































































































Результаты поиска

Содержание KINO-690S1

Отзывы:

IEI Technology KINO-690S1, Руководство пользователя, Страница: 91 / 229

Результаты поиска

Содержание KINO-690S1

Отзывы: