manualshive.com logo in svg

IEI Technology KINO-690S1, Руководство пользователя, Страница: 204 / 229

Поделиться
Скачать
IEI Technology KINO-690S1 Скачать руководство пользователя страница 204

 

 

KINO-690S1 Mini-ITX Motherboard

Page 186 

B.1 DIO Interface Introduction 

The DIO connector on the KINO-690S1 is interfaced to GIO ports on the iTE Super I/O 

chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs 

and digital outputs are generally control signals that control the on/off circuit of external 

devices or TTL devices. Data can be read or written to the selected address to enable the 

DIO functions.   

 

NOTE: 

For further information, please refer to the datasheet for the iTE Super 

I/O chipset. 

B.2 DIO Connector Pinouts 

The following table describes how the DIO connector pins are connected to the Super I/O 

GPIO port 1. 

Pin 

Description 

Super I/O Pin 

Super I/O Pin Description 

1 Ground 

N/A 

N/A 

2 VCC 

N/A 

N/A 

3 

XIN0 

27 (GP20) 

General purpose I/O port 2 bit 0. 

4 

XOUT0 

23 (GP24) 

General purpose I/O port 2 bit 4. 

5 

XIN1 

26 (GP21) 

General purpose I/O port 2 bit 1. 

6 

XOUT1 

22 (GP25) 

General purpose I/O port 2 bit 5. 

7 

XIN2 

25 (GP22) 

General purpose I/O port 2 bit 3. 

8 

XOUT2 

21 (GP26) 

General purpose I/O port 2 bit 2 

9 

XIN3 

24 (GP23) 

General purpose I/O port 2 bit 6 

10 

XOUT3 

20 (GP27) 

General purpose I/O port 2 bit 7. 

 

 

Содержание KINO-690S1






































































































































































































































Отзывы:

Нет отзывов