IEC miniReStoramod Скачать руководство пользователя страница 9

Страница: 9 / 28

Modular Hi-Rise Replacement Series – MIY

INSTALLATION, OPERATION, & MAINTENANCE MANUAL

SECTION ONE — Receipt, Unpacking, & Inspection, Cont’d.

Special Arrangement Options

Sup

Ret

Sup

90°

Sup

Ret

Sup

Supply

90°

Sup

Ret

Sup

Ret

Sup

Supply

Sup

Ret

Sup

Ret

90°

Ret

Sup

Supply

Sup

Ret

Sup

Ret

90°

Ret

Sup

Supply

Triple-side Supply

Sup

Ret

Sup

Ret

Sup

90°

Sup

Ret

Sup

Ret

90°

Ret

Sup

NOTES: 1. For special supply/return arrangement options, please contact IEC for pricing and availability.

2. Any special suply/return arrangement may affect sound and performance.

3. Risers pictured are shown for reference purposes only and adhere to the IEC standard convention.

4. MRY/MIY equipment is designed to use existing risers, so risers are typically not sold with these models.

5. Riser supply-return configurations and temperatures should be labeled prior to demolition and must be verified

prior to installation, as they may differ from the IEC standard convention.

6. Special arrangements may require special supply grilles, baffling and lab testing to validate actual performance.

Sup

Ret

Sup

Ret

90°

Ret

Sup

Triple-side Supply

Sup

Ret

Sup

Ret

Sup

90°

Sup

Supply

Sup

Ret

Sup

Ret

90°

Ret

Sup

Supply

Sup

Ret

Sup

Ret

90°

Ret

Sup

Supply

Содержание miniReStoramod





























Результаты поиска

Содержание miniReStoramod

Отзывы:

IEC miniReStoramod, Инструкция по установке, эксплуатации и обслуживанию, Страница: 9 / 28

Результаты поиска

Содержание miniReStoramod

Отзывы: