manualshive.com logo in svg

IEC miniReStoramod, Инструкция по установке, эксплуатации и обслуживанию, Страница: 19 / 28

Поделиться
Скачать
IEC miniReStoramod Скачать руководство пользователя страница 19

Modular Hi-Rise Replacement Series – MIY

INSTALLATION, OPERATION, & MAINTENANCE MANUAL

19

SECTION FOUR — Start-Up, Cont’d.

Motor Control Voltage – Proportional/Analog Thermostat Settings

NOTES:  1.   The above minimum and maximum settings must be field-programmed into the proportional fan thermostat to ensure 

proper operation and adherence to published values.

 

2.   The minimum voltage settings must NOT be reduced further; otherwise, the electric heater will not maintain sufficient 

airflow. This can result in frequent nuisance tripping of the thermal cut-out protection, which temporarily disables the 

electric heater.

 

3.   Increasing voltage settings of High fan speed may result in higher sound power values than what are published by the 

manufacturer.

 

4.   Please contact the Factory for special CFM or external static pressure applications.

Unit Model 

and Size

Total # of Coil 

Rows

Unit Voltage 

(V/PH/Hz)

Proportional/Analog T’stat 

Fan Speed Limits (VDC)

Tested CFM values at 0” ESP

Max

Min

High

Low

MIY04

3

120V/1/60

6.37

3.65

386

203

MIY04

4

120V/1/60

6.28

3.63

380

202

MIY04

5

120V/1/60

6.28

3.63

374

199

MIY04

3

208V/1/60

7.23

4.14

384

201

MIY04

4

208V/1/60

7.12

4.20

375

200

MIY04

5

208V/1/60

7.41

4.20

378

198

MIY04

3

240V/1/60

6.85

4.14

387

210

MIY04

4

240V/1/60

6.89

4.13

379

203

MIY04

5

240V/1/60

7.04

4.25

384

208

MIY04

3

277V/1/60

7.15

4.14

389

203

MIY04

4

277V/1/60

7.04

4.22

377

207

MIY04

5

277V/1/60

7.05

4.25

380

205

Figure 12. Proportional Fan Thermostat

Neptronic thermostat offered  

by manufacturer 

(Field Programmed)

Содержание miniReStoramod





























Отзывы:

Нет отзывов