IDTECK FINGER007 Series Скачать руководство пользователя страница 7

 

HELP3

   

(Procedure Based on FINGER007)

 

Re-register the card to the device and try again. 

The following describes the procedure of fingerprint registration.

 (Pay special attention to 

STEP8

 and 

STEP9

.) 

 

1. 

From  the  stand-by  screen,  enter  the  8-digit  Master  ID  and 

press  the                button  using  the  keypad.  (The  default 

Master ID is “00000000”) 

 

2. 

After  the  “Master  Password”  screen  is  displayed,  enter  the 

Master Password. (The default password is “3141”) 

 

3. 

The “Mode Selection” screen appears. Then, press             

to move to the F3 SETUP MENU. 

 

4. 

The “ID REGISTRATION” screen appears.   

 

5. 

press                ,  then  you’ll  be  asked  whether  to  register  the 

user  by  a  card  or  using  the  keypad.  If  you’d  like  a  card 

registration, press                , or, if you’d like to manually enter 

the ID using the keypad, press                .   

 

6. 

If  the  “Key  Input  ID”  message  appears,  enter  the  User  ID 

using  the  keypad.  If  the  “Put  ID  Card”  message  appears, 

present a card to the reader.   

 

7. 

You’re  required  to  enter  the  Password  (PW),  Time  Schedule  (TS), 

Reader  to  be  assigned  (RD),  and  Use  of  Fingerprint  (FP).  Enter 

appropriate values. For fingerprint registration, enter 1 in the FP field. 

 

8. 

After  the  “To  Register  FP  Put  your  FP  on”  message  appears 

and the fingerprint sensor  is lit, place the finger you’d like to 

register on the fingerprint sensor.   

 

9. 

If  the  “Lift  and  Put  FP”  message  appears,  lift  your  finger  up 

and  wait  until  the  fingerprint  sensor  is  lit  again.  After  the 

fingerprint sensor is lit, place your finger down again.   

NOTE:  If  the  Dual  Finger  Mode  is  applied,  place  a  finger 

different from the one used in 

STEP 8

.) 

 

10. 

If  the  “ID  Registered”  message  is  displayed,  the  ID 

registration has completed successfully. Return to the Stand-

by  mode  by  pressing            .  If  a  different  message  is 

displayed, repeat the registration from 

STEP4

MODE SELECTION 

RF ONLY 

FINGER_007    [F1] 

MM/DD   hh:mm:ss 

Master   Password 

[ _ _ _ _ ] 

ENT

F3 

Key Input ID 

->  _ _ _ _ _ _ _ _  

XXXXXXXX 

PW____TS__RD_FP_ 

To Register F P  

P u t   yo u r   F P  o n . .  

ID REGISTRATION 

 

ENT

Lift  and Put F P  

WA IT ING… 

ID  Re gist e re d  

[ Q # 1: 4]    [Q#2:3]  

Put ID Card 

Scanning… 

ESC

CARD & Key Use 

1-Card, 2-Key 

Содержание FINGER007 Series










Отзывы: