manualshive.com logo in svg

iDRY MINI, Руководство пользователя

Поделиться
Скачать
iDRY MINI Скачать руководство пользователя страница 33

Troubleshooting 

Troubleshooting and Alarms 

ISSUE

Possible Cause

Solution

No power at start up

No power to Kiln

Verify facility power to 
Kiln is turned on

Main disconnect not turned on

Turn on the main 
disconnect

Loose wire

A power wire may be 
loose or disconnected

Fuse Blown

In the control panel 
box. Located in the top 
right corner. Check 
fuses.

Vacuum pump does not run

No power to the pump

Vacuum Pump Motor 
Starter Fault. Reset 
starter.

No water to the pump

Check water 
connection and flow 
rate

Pump is seized 

Using the seized pump 
instructions. You will 
need to rotate the 
motor internal to the 
pump.

Vacuum pump runs but no 
vacuum in chamber

Door not closed

Verify there is no 
obstruction between 
the door gasket and 
kiln.




verify the door is 
closed tightly.

No water to the pump

Verify you have the 
proper water pressure 
going to the kiln.




On the water flow 
meter. Verify the 
display is showing 
water flow.

Flow Meter display is reading zero

Check water flow and 
pressure.

Check Rotation

Check Rotation

ISSUE

iDRY Turbo User Manual

© 2021 iDRY, LLC

33

Содержание MINI












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды