background image

 English 

 

18 

 

 

 
 
 

 
 
 

11.

 

MAINTENANCE - PLAN 

 

MAINTENANCE OPERATIONS - STEAM 

Interval (hours of service life) 

Cleaning of the fuel tank 

200 hours 

Cleaning of water filter and fuel filter 

100 h 

Check up sensors (boiler and water tank) 

150 h 

Check up burner electrodes 

200 h 

Descaling Procedure 

200 h 

 

 

MAINTENANCE OPERATIONS – PRESSURE WASHER 

Interval (hours of service life) 

Cleaning of detergent filter 

50 h 

Cleaning of water filter 

50 h 

Check up pump oil 

100 h 

Replace pump oil 

500 h 

 

 

 
 

 
 
 
 
 
 
 
 
 
 

MAINTENANCE – IMPORTANT SAFETY PRECAUTIONS  

Any maintenance (cleaning) operation must be done only after the following operations have 
been performed: 

 

The machine has unplugged  

 

The boiler has been properly drained (use drainage valve 8, fig.02) 

 

The pressure gauge reads 0 bar  

 

Wait around 30 minutes after the discharging operation to make sure the machine 
cools down.  

 

Remove the cover by unscrewing the placeholder screw 12 (fig.09)

 

 

 

 

It is strictly forbidden to operate or repair the ASTRA STEAMER HYBRID 
without burn proof safety gloves and appropriate ear protection. 

 

 

Содержание Astra Steamer Hybrid

































Отзывы: