IDK MSD-702UHD Скачать руководство пользователя страница 14

Страница: 14 / 150

MSD-701UHD / 702UHD / 801UHD/ 802UHD User’s Guide

4 Features

■

Video

・

Up to 4K@60 (4:4:4)

・

HDCP 1.4 / 2.2

・

Up to 492 ft. (150 m) over Cat6 cable (Long reach mode)

・

Motion adaptive I/P conversion

・

Scan conversion (independent for each output)

・

Aspect ratio control

・

Seamless switching

・

A/D conversion

・

Anti-snow (automatic recovery from HDCP error)

■

Audio

・

A/D, D/A conversion

・

Volume adjustment

・

Lip sync

■

Control Input

・

RS-232C

・

LAN

・

Command control

■

Control output

・

Control command output (e.g. controlling projector)

・

PJLink

・

Power control of sink device over CEC

・

Contact closure

■

Others

・

Power over HDBaseT (PoH) power feeding (HDBaseT input)

・

EDID emulation

・

All functions and configuration settings accessible through browser

・

Automatic input detection and switching

・

Audio breakaway enables independent audio and video switching

・

Cross point memory

・

Preset memory

・

Last memory

・

Connection Reset

・

Security lock

For Long reach mode, up to 1080p (24 bit) resolutions are supported.

Seamless switching with a black frame.

Only for MSD-801UHD / 802UHD.

Tip:

For Long reach mode, use IDK

’

s HDBaseT products supporting 328 ft. (100 m).

Содержание MSD-702UHD























































































































































Результаты поиска

Содержание MSD-702UHD

Отзывы:

Бренды по названию

Популярные бренды

IDK MSD-702UHD, Руководство пользователя

Результаты поиска

Содержание MSD-702UHD

Отзывы:

Бренды по названию

Популярные бренды