idi 1000F-1 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 27

idi 1000F-1 Скачать руководство пользователя страница 18

Installation and Maintenance Guide for IDI Suspension System mounted to Canon DST-1000A Rails

L240-1429 REV A Image Diagnostics, Inc.

Page

18

INSTALL STATIONARY CABLE HANDLING ASSEMBLY

1.

Determine which end of the IDI Cross Rail the Stationary Cable Handling Assembly will be
positioned onto.  If it is to be at the far end of the rail, slide the assembly into the rail track
prior to positioning the Mobile Cable Handling Assembly.  If assembly is to be positioned at
the near end of rail, slide into the rail after positioning the Mobile Cable Handling Assembly.
The Stationary Cable Handling Assembly is typically mounted approximately 6 inches (15cm)
from the end of the rail.  See Figure 11.

Figure 9

2.

Apply Loctite #242 to threads on set screws and then tighten until secured in place.

3.

Remove retainer by removing both button head cap screws.

4.

Place cable hose into cable carrier clamp.

5.

Reinstall retainer and mounting screws.

«
...
16
17
18
19
20
...
»

Содержание 1000F-1




























Отзывы:

Нет отзывов