IDEAL 41-392-98 страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 60

background image

SERVICING

Mini

Installation & Servicing

45

62 DHW HEAT EXCHANGER

REPLACEMENT

Mini C only

1 Disconnect the electrical supply.
2 Remove outer casing (refer to frame 36).
3 Close the isolating cocks of the CH circuit and DHW

supply at the bottom of the boiler.

4 Release system pressure by opening the main circuit

drainage cock.

Do not release CH pressure using the pressure relief

valve. It may cause debris within the system to foul

the valve.

5 Release the pressure of the DHW circuit by opening a hot

tap.

6 Remove the diverter valve actuator (see frame 63).
7 Completely unscrew the two Allen key screws A which

hold the exchanger to the brass groups.

A

8 Move the exchanger towards the rear of the boiler and

extract it.

9 Re---assemble in the reverse order.

Attention. When reassembling the exchanger be sure to

put the off center location/securing pin indicated towards

the left side of the boiler.

63 DIVERTER VALVE ACTUATOR

REPLACEMENT

Mini C only

1 Disconnect the electrical supply.

2 Remove front casing panel (refer to frame 36).

3 Disconnect the connectors A.

4 Remove the fixing spring B and remove the actuator C.

Re---assemble in reverse order.

When reassembling the actuator, refer to the wiring diagram

in frame 22 for the correct wiring connection.

B

A

C

SER

VI

CI

N

G

«
...
43
44
45
46
47
...
»

Содержание 41-392-98





























































Отзывы:

Нет отзывов

Похожие инструкции для 41-392-98

Prestige Slol 250

Бренд: TriangleTube Страницы: 89

Бренд: Argo Страницы: 24

Бренд: Nibe Страницы: 12

Greenstar Heatslave 18/25

Бренд: Worcester Страницы: 20

Бренд: Worcester Страницы: 36

Бренд: Worcester Страницы: 96

Бренд: Worcester Страницы: 100

Бренд: Aerco Страницы: 122

Бренд: Worcester Страницы: 16

Бренд: Worcester Страницы: 21

BAYKAN 24kW Sun Premix

Бренд: GasTech Страницы: 20

Бренд: SilverPoint Страницы: 4

Бренд: Sime Страницы: 12

Бренд: Radiant Страницы: 68

Бренд: hajdu Страницы: 43

Бренд: Danfoss Страницы: 28

Бренд: Halstead Страницы: 28

PLANET DEWY 30 BFR

Бренд: Sime Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды