IDEAL 41-392-98 Скачать руководство пользователя

Страница: 34 / 60

SERVICING

Mini

--- Installation & Servicing

REPLACEMENT OF COMPONENTS

42 GENERAL

When replacing any component:

1 Isolate the electricity supply at the switched spur.

N.B.

Turning the boiler “ON/OFF” switch does not isolate

the live supply to the boiler.

2 Turn off the gas supply.
IMPORTANT. When work is complete the inner case cover

must be correctly fitted, ensuring that a good seal is made.

THE BOILER MUST NOT BE OPERATED IF THE INNER

CASE COVER IS NOT FITTED.

If the CH and/or the DHW circuits have been emptied:

3 Open the hydraulic circuit cocks, refill / re---pressurise

pipeworks and vent the system.

4 Test fire the boiler
5 Disconnect the filling loop.

43 SPARK AND DETECTION

ELECTRODE REPLACEMENT

1 Disconnect the electrical supply.
2 Remove outer and inner casing (refer to frame 36).
3 Open the combustion chamber and disconnect the

electrodes leads.

4 Remove the burner. Refer to frame 37.
5 Undo the screws that hold the electrodes and remove.
6 For models

Mini C24

Mini C28

Mini S24

Mini S28

, fit

new electrodes as necessary following the sequence

illustrated.

Ignition 1

Ignition 2

Detection 3

7 Check the spark gap.

4 mm (5/32”)

Ignition

Detection

Male

Female

10 mm

Burner blade

(3/8”)

Mini C24

Mini C28

Mini S24

Mini S28

4 mm (5/32”)

Ignition

Detection

Male

Female

10 mm

Burner blades

(3/8”)

10 mm

(3/8”)

Mini C32

8 Re---assemble in reverse order.
9 Check the ignition and operation of the burner.

44 BURNER REPLACEMENT

1 Remove the burner as explained in frame 37
2 Remove the spark and detection electrodes.

Refer to frame 43.

3 Fit the electrodes on the new burner and check the spark

gap.

4 Re---assemble in reverse order.
5 Check the operation of the boiler.

SER

Содержание 41-392-98





























































Результаты поиска

Содержание 41-392-98

Отзывы:

Похожие инструкции для 41-392-98

Бренды по названию

Популярные бренды

IDEAL 41-392-98, Установка и обслуживание

Результаты поиска

Содержание 41-392-98

Отзывы:

Похожие инструкции для 41-392-98

Бренды по названию

Популярные бренды