Ideal Heating III Series Скачать руководство пользователя страница 6

Страница: 6 / 44

SECTION 1 - GENERAL

1.5 SAFETY

Current Gas Safety (installation and use) regulations or rules

in force:

The appliance is suitable only for installation in the specified

countries and should be installed in accordance with the rules in

force.
In GB, the installation must be carried out by a Gas Safe

Registered Engineer. It must be carried out in accordance with the

relevant requirements of the:
• Gas Safety (Installation and Use) Regulations
• The appropriate Building Regulations either The Building

Regulations, The Building Regulations (Scotland), Building

Regulations (Northern Ireland).

• The Water Fittings Regulations or Water byelaws in Scotland.
• The Current I.E.E. Wiring Regulations.
The appliance must be installed so that the electrical power socket

is not switchable.
If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified persons in

order to avoid hazard.
Mains supply and system wiring must be through a common

isolator.

Where no specific instructions are given, reference should be made

to the relevant British Standard Code of Practice.

In other countries the installation must be carried out by a qualified

and competent Gas Installer. In the approved country the boiler

is installed, this must be in accordance with their current rules in

force.
Detailed recommendations are contained in the following British

Standard Codes of Practice:

BS. 5482: Part 1 2005 -

Code of Practice for domestic butane

and propane gas burning installations in permanent dwellings,

residential park homes and commercial premises.

BSEN1949:2011+A1:2013

- Specification for the installation

of LPG systems for habitation purposes leisure accomodation

vehicles and in other road vehicles.

Health & Safety Document No. 635.
The Electricity at Work Regulations, 1989.

The manufacturer’s notes must NOT be taken, in any way, as

overriding statutory obligations.

IMPORTANT.

These appliances are CE certificated for safety

and performance. It is, therefore, important that no external

control devices, e.g. flue dampers, economisers etc., are directly

connected to these appliances unless covered by these Installation

and Servicing Instructions or as otherwise recommended by

Morco

in writing. If in doubt please enquire.
Any direct connection of a control device not approved by

Morco

could

invalidate the certification and the normal appliance warranty. It

could also infringe the Gas Safety Regulations and the above

regulations.

1.6 SAFE HANDLING OF SUBSTANCES

No asbestos, mercury or CFCs are included in any part of the boiler

or its manufacture.

Содержание III Series













































Результаты поиска

Содержание III Series

Отзывы:

Похожие инструкции для III Series

Бренды по названию

Популярные бренды

Ideal Heating III Series, Технические инструкции

Результаты поиска

Содержание III Series

Отзывы:

Похожие инструкции для III Series

Бренды по названию

Популярные бренды