Ideal AKE GASTRO A Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 25

Ideal AKE GASTRO A Series Скачать руководство пользователя страница 25

REPAIR MANUAL

REFRIGERATION UNIT

– ELECTRICS

Rev

. 21B

RM-Refrigeration Unit - electrics_EN

page 25 of 25

4 Cleaning and Final Inspection

Clean the unit thoroughly and remove any dirt (drilling chips, etc.).

Only use suitable cleaning agents!

Observe all information in the operating manual in Chapter 3.4.2.

Connect all electrical connections/cables and install all other dismantled parts in reverse order.

Check the device for completeness (no loose parts present).

Symbolic photo

After conversion of the unit

After the conversion work, the unit must be returned to its original condition in order to
ensure perfect operation of the unit.

All steps for commissioning after each repair of the device are described in the relevant
operating manual in Chapter 3.1.

Connect the device to the power supply with the mains plug, and check that it is functioning properly
(operate all control elements, switches, etc.)

Danger from electrical voltage on live components

The power supply must be disconnected before all conversion work. Dazu das Gerät
ausstecken oder allpolig vom Netz trennen. This to be carried out exclusively by an authorised
specialist.

«
...
23
24
25

Содержание GASTRO A Series


























Отзывы:

Нет отзывов