Ideal AKE GASTRO A Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 25

Ideal AKE GASTRO A Series Скачать руководство пользователя страница 21

REPAIR MANUAL

REFRIGERATION UNIT

– ELECTRICS

Rev

. 21B

RM-Refrigeration Unit - electrics_EN

page 21 of 25

3.7 Repair of lighting unit

Additional electrical components are installed depending on the model. Please contact your service
partner or the manufacturer regarding this.

3.7.1 Repair of LED light strips

Depending on the model variant, different LED light strips may be installed. The following repair
instructions may differ from the respective model. Contact your service partner or the manufacturer for
more information. See also see chapter 1.5 of the operating manual for the respective unit.

No.

Description/article

01:12:00  LED light strip
01:13:00  LED light strip
01:14:00  LED driver (LED transformer)

Symbolic photo

Remove the defective light strip from the mount (squeeze the clip at the corners), unscrew the plug
connector or alternatively disconnect the power cable from the distributor terminal, and pull it out of the
guide rail.

LED light strip including clip holder

Push-in fitting

Distributor terminal

Insert a new original spare part, install the cable with suitable fastening materials (cable ties) and
connect it according to the valid product-specific wiring diagram.

«
...
19
20
21
22
23
...
»

Содержание GASTRO A Series


























Отзывы:

Нет отзывов