background image

PRT-RDM2-PCB 

Protege Mini 2 Reader Expander 

Installation Manual | March 2015   

15

 

 

Replace 'xxx' with the appropriate address of the Reader Expander that you are programming. 

1K5 OHM

LED

+      -

DO

L2

D1

L1

BZ

R1

R1

R1

R1

R1

R1

R1

 

Example Open Collector Output Connection (LED) 

 

 

Warning: The PGM outputs 3 to 8 can switch to a maximum capacity of 50mA each. Exceeding this 
amount will damage the PGM output. 

 

 

5.3

 

PGM Beeper Outputs Special Functions (5 and 8) 

The PGM beeper outputs 5 and 8 on the Reader Expander provide special diagnostic information when a card 
is presented. The following table shows the beeper modes of operation. 

 

Function 

Description 

2 Beeps 

Access Granted. The lock will activate and allow access to the door the card has been 
presented. 

4 Beeps 

Offline Access Granted. This is generated ONLY if the reader expander is operating 
offline and the mode of offline operation allows access. 

1 Long Beep 

Offline Access Denied. This is generated ONLY if the reader expander is operating offline 
and the mode of offline operation prevents this card from being allowed access. 

1 Long Beep   
1 Short Beep 

Access Denied Card Number Not Known. The card number is not known in the system. 
The card that has been presented to the reader could not be matched to a valid user in 
the system. 

1 Long Beep   
2 Short Beeps 

Access Denied Door Group. The user is denied access because they do not have 
access to the door. This error will also be generated if the door group is not set or the 
door group schedule is not valid. 

1 Long Beep   
3 Short Beeps 

Access Denied Area Group. The user is denied access because they do not have 
access to the area that is being controlled by the door. If the area that the door is 
associated with is armed, and the user does not have this area in their area disarm 
group, they will be denied access. This also depends on the area group settings for the 
door. 

1 Long Beep   
4 Short Beeps 

Access Denied Access Level. The user is denied access because they do not have a 
valid access level or the access level they are assigned is currently outside the 
programmed schedule. 

 

 

Содержание Protege PRT-RDM2-PCB



























Отзывы: