ICS 536-E страница 18 Скачать руководство пользователя

Страница: 18 / 40

536-E OPERATOR MANUAL

Names & Terms

ICS 536-E NAMES AND TERMS

Bar clamp plate

The plate between the guidebar and side cover that clamps the guidebar

to prevent movement during operation.

Bar slot

The slot feature on the guidebar that fits over the bar clamp plate.

Bystander safety zone

At minimum, a 20 ft (6 m) circle around the operator that

must remain free from bystanders, children and pets.

Chain pitch

The distance between any three consecutive rivets on the

chain divided by two.

Chain tensioning screw

An adjustment screw used to set proper tension on the

chain and compensate for chain stretch from normal use.

Front handle

The support handle located at or toward the front of the power cutter intended to

be gripped by the left hand.

Guidebar

A railed structure that supports and guides the chain.

Kickback

The rapid backward and/or upward motion of the guidebar, occurring when the

chain near the top area of the nose of the guidebar contacts a foreign object or

snags in the workpiece.

Mud flap

A barrier to deflect slurry, cutting debris and other projectiles from

operator.

Powerhead

A power cutter without the chain or guidebar.

Pushback

The rapid backward motion of the guidebar, occurring when the chain on

the top straight portion of the guidebar contacts a foreign object or

snags in the workpiece.

Rear handle

The support handle located at or toward the rear of the power cutter

intended to be gripped by the right hand.

Rear hand guard

A structural barrier at the bottom of the rear handle to protect the operator in case

the chain breaks or derails.

Side cover

The component on the powerhead that covers the drive sprocket and directs

debris away from the operator during use.

Side cover nuts

The components on the side cover that secure the side cover to the powerhead

Trigger lock-out

A device that prevents the unintentional operation of the trigger until

manually released.

Trigger

A mechanism that controls motor operation.

WallWalker®

A device used as a fulcrum to provide mechanical advantage during cutting.

Water shut-off valve

A mechanism that controls water delivery and flow to the guidebar and chain.

.444

÷2

determine chain pitch

Содержание 536-E









































Результаты поиска

Содержание 536-E

Отзывы:

Похожие инструкции для 536-E

Бренды по названию

Популярные бренды

ICS 536-E, Руководство оператора

Результаты поиска

Содержание 536-E

Отзывы:

Похожие инструкции для 536-E

Бренды по названию

Популярные бренды