background image

33 

 

 

Put the middle button at the centre of the zone you want to zoom in, and move the mouse, you 

can view an interface shown as in Figure 4-30. 

             

         

 

Figure 4-30 

Right click mouse to cancel zoom and go back to the original interface. 

3)  Manual record function 

It is to backup the video of current channel to the USB device. System can not backup the video of 

multiple-channel at the same time.   

Click button

, system begins recording. Click it again, system stops recoridng. You can find the record 

file on the flash disk. 

4)  Manual Snapshot 

Click 

  to snapshot 1-5 times. The snapshot file is saved on the USB device or HDD. You can go to 

the Search interface (chapter 4.9) to view. 

 

5)  Bidirectional talk   

If the connected front-end device supports bidirectional talk function, you can click this button. Click 

button 

  to  start  bidirectional  talk  function  the  icon  now  is  shown  as

  .  Now  the  rest 

bidirectional talk buttons of digital channel becomes null too. 

Click 

  again,  you  can  cancel  bidirectional  talk  and  the  bidirectional  talk  buttons  of  other  digital 

channels become as

 

6)  Remote device   

Shortcut menu. Click it to go to the remote device interface to add/delete remote device or view its 

corresponding information. Please refer to chapter4.5.2 for detailed information. 

 

4.6.3

  Right Click Menu   

After  you  logged  in  the  device,  right  click  mouse,  you  can  see  the  short  cut  menu.  Please  see  Figure 

4-31. 

 

Window split mode: You can select window amount and then select channels.   

 

PTZ: Click it to go to PTZ interface.   

 

Auto  focus:  It  is  to  set  auto  focus  function.  Please  make  sure  the  connected  network  camera 

supports this function.   

 

Color setting: Set video corresponding information.   

 

Search: Click it to go to Search interface to search and playback a record file.   

Содержание NVR-7508K









































































































































































































































Отзывы: