Owner’s Manual Compact Range
iCoolsport.com
Page 9
YOU Can DisPLaY The POOL TeMPeRaTURe
aT FULL-sCReen siZe.
if you touch the number in the pool temperature window on
the Main Operation screen for a few seconds the screen will
change to a full-screen display of that temperature.
This is useful if you wish to monitor the system from a
distance.
The pre-set temperature and the outside temperature
continued to display in smaller windows for your reference.
To return to the main operating screen touch the
BaCK 1
button.
TO sTOP The sYsTeM aT The enD OF YOUR ReCOveRY
sessiOn
There are several ways to stop the system and close it down. You can stop the cooling system by touching
the
sTOP sYsTeM
button, in this case the pump will continue to run. You can stop to pump at any time by
touching the
sTOP PUMP BUTTOn
. alternatively you can stop everything by touching the
aLL sTOP BUTTOn
.
alternatively you can simply switch off the main power. if you use the
aLL sTOP BUTTOn
the fan may continue
to run for a short time to cool the cabinet. Because the system will not run without water, touching
sTOP PUMP
also stops the heat pump if it is already running.
eMPTYinG The POOL UsinG The PUMP.
You can use the main circulating pump to empty the water from the pool by detaching the hose that runs from
the pump to the iCool. The pool water can then be directed to a drain. The pump can be turned on and off at any
time using the
PUMP
sTOP/sTaRT
button.
FUnCTiOns OF The TOUCh BUTTOns
sYsTeM seTTinGs
When your iCool starts up, the first screen you will see offers you a
sYsTeM seTTinGs
button.
The BesT seTTinGs aRe aUTOMaTiCaLLY seLeCTeD
so there is usually no need to use this feature.
The three settings you can change are the fan speed range, the temperature from degrees Centigrade to
Fahrenheit and the sound level from the screen.
Main COOLinG Fan sPeeD
. This allows you to set the main cooling fan to either
nORMaL
or
QUieT MODe
.
Generally you should always leave it in the nORMaL mode
which is fully
automatic and allows the system to control the fan speed to give the very best efficiency and
fastest cooling.
if you are in a very quiet environment you
can select
QUieT MODe
, but you must be
aware that this will reduce the cooling ability
of the system, however it will be quieter overall as the fan will
not run higher than 60% of maximum
unless there is a risk
of overheating, in which case the safety system will turn the
fan back to high no matter what the setting.
The
nORMaL
setting is used to give absolute maximum cooling power
where higher fan noise is not a problem. On a normal day
this gives about 30% more cooling than in the
QUieT MODe.
if cooling seems lower than normal, check to see if this
feature was previously set to Quiet Mode.
TeMPeRaTURe DisPLaY sCaLe
This can be set to either Centigrade or Fahrenheit and this changes all of the
displays throughout the entire system. When you first start the iCool it will normally start in Centigrade as this
is the world standard.
Due to complex decimal calculations between Cº and Fº there may be minor difference in
the true Fº displays.
This has no effect on actual cooling accuracy.
The
sOUnD LeveL
adjusts the sounds made by touching the screen and by the alarms. normally it should be
left on high to assist with settings and to make sure alarms are heard.
a
red
dot indicates which setting is selected in each of the available settings.
14
10
25
