iCool LITE, Руководство пользователя, Страница: 5 / 18

05
Owner’s manual for iCool Recovery Systems
Your iCool Lite can only be used with the voltage marked on the
machine, IT IS NOT MULTI VOLTAGE. The voltage is marked under to the
main power socket. It will be either 110volts (USA, Japan) or 220volts
(Europe etc)
BUILT IN SAFETY SYSTEMS
Your iCool system has many safety features to protect against such
things as a loss of water flow, overheating of the system, or any chance of
the user receiving an electrical shock. If any such potentially dangerous
things should occur, in most cases your iCool will shut itself down and a
red warning screen will appear to assist you to identify and correct the
problem. In the case of overheating, the main fan will continue to run for
some time until the temperature is safely back to normal.
For the safety of users, any leakage of even a small amount of electrical
current will cause the system to instantly remove all electrical power.
In the unlikely event that your system shuts itself down for any of these
reasons, you must identify and correct the problem that has caused the
safety systems to operate before allowing anyone to use the system.
PLEASE TEST THE EARTH LEAKAGE SAFETY DEVICE REGULARLY
The main power switch is also part of the electrical safety circuit that
can prevents the possibility of electric shock. It is essential to test this
safety system each time you use the iCool to make certain it is operating
correctly. This is very easy to do and takes only a few seconds.
Turn on the main switch (blue colour) and then press the orange test
button marked T just above the switch. If the safety system is working
normally, pressing the test button will cause the main power switch to
shut off instantly.
After a successful test, reset the main switch to ON to begin normal
operation. If pressing the test button fails to instantly shut off the power
switch DO NOT USE THE SYSTEM until you contact iCool for advice.
Failures of this system are very rare.
Occasionally you may experience some difficulty getting the water to
flow correctly through your iCool due to trapped air in the system or
the hoses.
As you gain experience using an ice bath system you will learn to
overcome this quickly and easily.
ABOUT PUMPS
Water flow through your iCool Lite is produced by a high-quality long life
circulating type pump that is fitted with a water filter to assist in keeping
the water in your pool clean.
Circulating type pumps are not self priming, they can lift and move water
reliably for many thousands of hours, but due to the long life design they
can not provide suction to begin the flow if there is air trapped anywhere
in the pump or hoses. Self priming type pumps are not used because
they are generally not as reliable over long periods and not suitable for
this type of system.
Like all circulating pumps, the pump with your iCool can not begin to
operate unless it is has a head of water above the pump and any air
tapped in the system is removed. Therefore, before you start, the water
in the pool must be above the pump inlet port. There must be no air
trapped in the supply hose and no part of the hose from the pool to the
cooling system can be above the level of the water because this traps
air which can prevent water flow from starting.
There are several easy ways to clear trapped air in the system. For
example, by touching the PUMP ON-OFF button 3 or 4 times so that the
pump is off for about 5 to 10 seconds each time. The surge when the
pump starts can often clear the trapped air, but it may take a few times
if there is a lot of trapped air.
If you still do not have a good flow of water try detaching the water hose
from the outlet fitting on the iCool. This is the hose connected to the top
fitting that returns the water to your pool. Now turn on the pump until
a good clear flow of water comes out of the top connector fitting, then
quickly snap the hose back into position on the iCool and lock it. This is
the most effective way to clear an air blockage so that water can flow
normally.
YOU ONLY NEED TO BLEED THE SYSTEM ONCE FOR EACH SET UP.
Once primed of air, (and until it is emptied or moved), the system will
remain primed until and water will normally flow instantly each time you
start the pump
NEVER OPERATE THE PUMP WITHOUT WATER FLOWING.
Water
pumps can not operate for long periods without water because the
water provides the lubrication to the bearings.
IMPORTANT
ADVICE
SAFETY NOTICE
OBTAINING THE CORRECT FLOW OF WATER
WARNING
To ensure safe operation the power outlet you use must have a
proper earth connection