14
CABLE ASSEMBL
Y
22. Attach the Long Cable (23) to the Small ÒUÓ-
Bracket (67) with a 1/4Ó Nylon Locknut (2)
and a 1/4Ó Flat Washer (10).
Do not com-
pletely tighten the Nylon Locknut. It
should be threaded onto the end of the
Cable so only a couple of threads are
showing above the Nylon Locknut, as
shown in the inset drawing.
Attach the Small ÒUÓ-Bracket (67) to the
Weight Tube (63) with the 5/16Ó x 1 3/4Ó Bolt
(72) and a 5/16Ó Nylon Locknut (3).
23. Attach the Backrest (41) to the Front Upright
(42) with two 1/4Ó x 2 1/2Ó Screws (43) and
two 1/4Ó Flat Washers (10).
24. Press a 1 1/2Ó Square Inner Cap (32) into the
Seat Frame (36).
Insert the 1/4Ó x 2Ó Carriage Bolt (38) through
the centre hole in the Seat Plate (37). Attach
the Seat Plate to the Seat (13) with two 1/4Ó x
1/2Ó Screws (18).
Insert the 1/4Ó x 2Ó Carriage Bolt (38) into the
indicated hole in the Seat Frame (36).
Tighten a 1/4Ó Nylon Locknut (2) with a 1/4Ó
Flat Washer (10) onto the Carriage Bolt.
Attach the other end of the Seat (13) to the
Seat Frame (36) with the 1/4Ó x 2Ó Screw (24)
and a 1/4Ó Flat Washer (10).
24
22
23
23
3
42
41
10
13
10
2
18
38
37
36
32
24
72
67
2
10
63
43
SEA
T ASSEMBL
Y
23
57
10
2
CABLE ASSEMBL
Y
17
15
50
20
21
57
15
23
6
66
48
7
16
23
68
16. Route the Long Cable (23) around the ÒVÓ-
Pulley (6) on the Right Arm (48).
Be sure that
the Cable is in the groove of the ÒVÓ-Pulley
and that the Long Cable Trap (50) is turned
to hold the Cable in place.
Tighten the 3/8Ó x
2 1/2Ó Bolt (7) and the 3/8Ó Nylon Locknut (not
shown).
Route the Long Cable (23) around the 3 1/2Ó
Pulley (15) attached to the Pulley Bracket (20).
Be sure that the Cable is in the groove of
the Pulley and that the Cable Trap (66) is
turned to hold the Cable in place.
Tighten
the 3/8Ó Nylon Locknut (21) and the 3/8Ó x 2Ó
Bolt (not shown).
Be sure that the 5/16Ó x 5Ó Bolt (68) is tight-
ened.
17. Refer to the inset drawing. If the 3 1/2Ó Pulley
(15) is pre-attached to the Long ÒUÓ Bracket
(57), remove it. Wrap the Long Cable (23)
around the 3 1/2Ó Pulley. Attach the Pulley and
two Pulley Covers (89) to the indicated hole in
the Long ÒUÓ-Bracket (57) with a 3/8Ó x 2Ó Bolt
(12) and a 3/8Ó Nylon Locknut (21).
Make sure
that the Pulley Covers are turned so the
wide tabs are on the indicated side.
Be sure that the Cable is in the groove of
the Pulley and that the Cable and Pulley
move smoothly.
11
23
21
12
89
Wide
Tabs
15
57
