Icom IC-M602 Скачать руководство пользователя страница 62

Страница: 62 / 78

SPECIFICATIONS AND OPTIONS

■

Specifications

General

• Frequency coverage

Transmit 156.025–157.425

MHz

Receive 156.050–163.275

MHz

• Mode

: FM (16K0G3E)

DSC (16K0G2B)

• Current drain (at 13.8 V) : TX high (25 W)

5.2 A typical

Max. audio

1.2 A typical

• Power supply requirement: 13.8 V DC ±15%

(negative ground)

• Frequency stability

: ±5 ppm

(–20°C to +60°C;
–4°F to +140°F)

• Antenna impedance

: 50

Ω

nominal

• Input impedance (MIC)

: 2 k

Ω

• Output impedance (audio) : 4

Ω

• Intermediate frequencies : 1st; 31.05 MHz, 2nd; 450 kHz

(CH 70 receiver) 1st; 21.7 MHz, 2nd; 450 kHz

• Dimensions : 220(W)

110(H)

109.4(D) mm

(Projections not included) 8

⁄

(W)

⁄

(H)

⁄

(D) in

• Weight

: 1350 g; 2 lb 16 oz

Transmitter

• RF output power

: 25 W and 1 W

• Modulation system

: Variable reactance frequency

modulation

• Max. frequency deviation : ±5.0 kHz
• Spurious emissions

: Less than –70 dBc

• Adjacent channel power

: More than 70 dB

• Audio harmonic distortion : Less than 10%

(at 1 kHz, 60% deviation)

• Residual modulation

: More than 40 dB

• Audio frequency response: +1 to –3 dB of 6 dB/octave

range from 300 Hz to 3000 Hz

Receiver

• Receive system

: Double conversion superheterodyne

• Sensitivity (12 dB SINAD) : Less than 0.32 µV

Less than 0.32 µV
(CH 70 receiver)

• Squelch sensitivity

: Less than 0.32 µV

• Spurious response

: More than 80 dB

• Intermodulation

: More than 80 dB

• Adjacent channel selectivity : More than 80 dB
• Hum and noise

: More than 40 dB

• Audio output power

: 5 W typical at 10% distortion

with a 4

Ω

load

All stated specifications are subject to change without
notice or obligation.

Содержание IC-M602















































































Результаты поиска

Содержание IC-M602

Отзывы:

Icom IC-M602, Инструкция по эксплуатации, Страница: 62 / 78

Результаты поиска

Содержание IC-M602

Отзывы: