17
SET MODE
17-6
Previous view
Tuner
Auto Start
OFF
or ON
Turns the automatic antenna tuner function ON
or OFF.
PTT Start
OFF
or ON
Turns the PTT Tuner Start function ON or OFF.
[TUNER] Switch
Manual or
Auto
Selects whether or not to store the AT-180’s sta-
tus by each band.
[SPEECH/LOCK] Switch
SPEECH/LOCK
, LOCK/SPEECH
Selects the function for
SPEECH
when pushed
or held down.
Lock Function
MAIN DIAL
or PANEL
Selects the dial lock function to prevent frequen-
cy changes by accidental movement of the tun-
ing dial.
Memopad Numbers
5
or 10
Sets the number of usable memopad channels.
MAIN DIAL Auto TS
OFF, LOW or
HIGH
Selects an option for the automatic tuning step
function. When rapidly rotating the main dial, the
tuning step automatically changes according to
the setting.
MIC Up/Down Speed
Slow or
Fast
Selects the steps per second when changing an
operating frequency by holding down the micro-
phone’s [
∫
]/[
√
] key.
[NOTCH] Switch (SSB)
Auto, Manual or
Auto/Manual
Selects the notch function for the SSB mode.
[NOTCH] Switch (AM)
Auto, Manual or
Auto/Manual
Selects the notch function for the AM mode.
SSB/CW Sync Tuning
OFF
or ON
Turns the Synchronous Tuning function ON or
OFF to shift the operating frequency by the offset
amount to keep receiving a signal when the oper-
ating mode is changed between SSB and CW.
CW Normal Side
LSB
or USB
Sets the carrier point for CW normal mode op-
eration to the LSB side or the USB side.
VOICE 1st Menu
VOICE-Root or
VOICE-TX
Select whether or not to directly select the voice
send menu, skipping the voice menu.
KEYER 1st Menu
KEYER-Root or
KEYER-SEND
Select whether or not to directly select the keyer
send menu, skipping the memory keyer menu.
Speaker Out
OFF or
ON
Selects to mute the speaker output.
MIC AF Out
OFF
or ON
Selects to output the received audio from the
[MIC] connector.
RC MIC
[F-1]
---, P.AMP/ATT, AGC, NB, NR, NOTCH,
RIT, AUTOTUNE/RX>CS, TS, MPAD,
M-CLR, BANK,
SPLIT
, A/B, DUP,
TONE/DSQL, COMP, TBW, METER,
DR, FROM/TO(DR), SCAN, Voice TX
(T1)
The functions listed to the left can be set to [F-1]
of the optional HM-151
REMOTE
CONTROL
MIC
.
[F-2]
---, P.AMP/ATT, AGC, NB, NR, NOTCH,
RIT, AUTOTUNE/RX>CS, TS, MPAD,
M-CLR, BANK, SPLIT,
A/B
, DUP,
TONE/DSQL, COMP, TBW, METER,
DR, FROM/TO(DR), SCAN, Voice TX
(T1)
The functions listed to the left can be set to [F-2]
of the optional HM-151
REMOTE
CONTROL
MIC
.
Mode Select
SSB,
CW,
RTTY,
AM,
FM,
WFM,
DV
(All boxes are checked.)
Disables the mode selection of the optional HM-
151
REMOTE
CONTROL
MIC
, to simplify operation.
Power OFF (With No Controller)
OFF or
ON
Selects whether or not to automatically turn OFF
the transceiver when the controller is disconnect-
ed from the transceiver.
REF Adjust
0 %~100 %
Sets a number to adjust for a zero beat with a
standard signal such as WWV or WWVH, for fre-
quency calibration.
Set mode items and Default settings (Continued)
NOTE:
The default settings shown below in bold are for the USA version.
The default settings may differ, depending on your transceiver version.