icetro IM Series страница 38 Скачать руководство пользователя | Manualshive

Страница: 38 / 52

background image

Tip 1:

Error Code 15 Potential Causes

Water level sensor (high-

level probe) is not detected

after 5 minutes.

Water:

•

Is the water supply to the machine open?

•

Is the water supply pressure below 20psi?

•

Does the water inlet solenoid have power to it from PCB?

•

Is the water inlet solenoid valve clogged with scale/debris?

•

Is there a water filter that’s overdue to be changed?

•

Does the water level sensor appear scaled up and in need of
cleaning?

•

Is water overflowing the water trough, indicating the water
level sensor is not sensing a full trough?

•

Is the trough full of water, but the water level sensor is
indicating that the machine is empty?

•

Is the dump valve stuck open?

IM-Series

Error Codes

38

«
...
36
37
38
39
40
...
»

Содержание IM Series





















































Отзывы:

Нет отзывов

Похожие инструкции для IM Series

Бренд: IceTech Страницы: 28

Бренд: cafe elite Страницы: 6

Бренд: Waring Страницы: 44

Ice Cream Parlor

Бренд: Waring Страницы: 24

NESPRESSO VERTUO NEXT

Бренд: Breville Страницы: 68

Бренд: Melitta Страницы: 12

Бренд: Caffitaly System Страницы: 100

Бренд: Schaerer Страницы: 34

Бренд: Caffitaly System Страницы: 64

Бренд: Cafection Страницы: 55

Бренд: Klarstein Страницы: 44

Бренд: Klarstein Страницы: 51

Бренд: Bestron Страницы: 88

Бренд: Unold Страницы: 110

Бренд: Brother Страницы: 163

Бренд: Brother Страницы: 84

Бренд: Brother Страницы: 166

Бренд: Brother Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды