Ice RS26L, Руководство оператора и каталог запасных частей

Страница: 9 / 41

9 ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
6. Press the Propel pedal, the machine start
scrubbing, the speed can be adjusted by
controlling the force of foot stepping, light is
slow, heavy is fast.
NOTE: Go slow on inclines and slippery
surfaces.
7. To stop scrubbing, turn off the 1-Step switch,
the scrub head will raise automatically, the
squeegee will also raise after a short delay (the
vacuum indicator flashing), please keep moving
until the dirty water is picked up, and then
release the propel pedal and stop scrubbing.
8. Turn off the machine.
BRaKe deVIce
The machine is drived by the Front drive wheel
(machine components, #10), that is equipped
with a brake device. When you release the Propel
pedal, the machine will stop travel, the park brake
will engage after a short delay.
The machine is equipped with a Brake pedal
(machine components, #8), that can be used to
control the machine if quicker stopping is needed
or if operating on an incline.
emeRGency Stop Button
The machine is equipped with an Emergency stop
button (machine components, #25), please push
it if an emergency, that will shut off all power of
machine and brake immediately.
To restart the machine, please reset the
Emergency stop button, and turn off the machine
and then restart.
NOTE: Please hold the steering wheel when
emergency stop.
WaRnInG: fire or explosion Hazard. do
Not Pick Up Flammable Materials Or Reactive
metals.
1. Go slow on inclines and slippery surfaces, go
slow when turn and reverse. Do not operate the
machine on inclines that exceed 7% (4°).
2. Drive machine in a straight path as possible,
avoid turning the Steering wheel too sharply
when machine is in motion. avoid sudden turns
except emergencies.
3. Do not keep the machine in the same position
with pad / brush spinning, keep the machine
moving to prevent damage to floor finish.
4. If the squeegee assembly leaves streaks on the
floor, raise the squeegee off the floor and wipe
the blades down with a damp cloth. Pre-sweep
the area to prevent leaving streaks on the floor.
5. To obtain the optimum cleaning performance,
you can adjust the brush pressure, solution
flow and detergent dosage as your required. If
poor picking up water performance is observed,
please stop scrubbing and check the squeegee
blade, adjust or replace if necessary.
6. If the dirty water path exceed the width of
squeegee, please adjust the side squeegee
assembly.
7. Pour a recommended defoamer into the
recovery tank if excessive foam appears.
WaRnInG: the foam do not activate
water level switch, excessive foam may result
in vacuum motor damage.
8. Press the Horn button (machine components,
#37) to alert if necessary.
9. The machine is equipped with a Warning light
(machine components, #17), you can select turn
ON or OFF by the Warning light switch (machine
components, #27).
10. If there is a fault code F10 (Batt low) on the
LED display screen, the machine will stop
scrubbing and alarm, please drive the machine
to charging.
11. If there is a fault code F08 (Rec Tank Full)
on the LED display screen, the vacuum motor
will stop working and alarm, please drive the
machine to drain water.
If there is a fault code F09 (Soln Tank Empty)
on the LED display screen, the Detergent
system will stop working and alarm, please fill
the solution tank.
12. If there are other fault codes on the LED
display screen, please turn off the machine,
eliminate the fault (please see FAULT CODES
AND ELIMINATE section), then restart machine.
13. For heavily soiled areas, please use DOUBLE
SCRUBBING mode.
The first time: Turn on the 1-Step switch, then
press the Vacuum motor switch (machine
components, #28), its indicator will turn off and
the squeegee will raise automatically, then start
to scrubbing this areas without picking up water.
The second time: turn on the Vacuum
motor switch, the squeegee will lower down
automatically, and then start to scrubbing and
picking up water.
14. If you only want to pick up water needn't
scrubbing, Turn on the Vacuum motor switch
(squeegee will lower down) and turn off the
1-Step switch (if it is ON), the scrub head will
raise and then start to working.
WHIle opeRatInG macHIne