background image

SAFETY PRECAUTIONS 

Carefully read and understand this manual before operating this machine.
This machine must be grounded!

This scrubbing machine shall be grounded while in use to protect the operator from electric 
shock.Grounding provides a path of least resistance for electric current. This machine is 
equipped with a cord having an equipment-grounding conductor

 

and grounding plug. The plug 

must be plugged into an appropriate outlet that is properly installed and grounded in accordance 
with all local codes and ordinances. Do not remove the ground pin under any circumstances.

This machine is for use on a nominal 110-volt circuit and 
has a grounding plug that resembles the plug illustrated 
in figure. Make sure that the machine is connected to 

an outlet having the same configuration as the plug. No 

adapter should be used with this machine.

This machine is intended for commercial use. It is constructed for use in an indoor environment 
and is nor intended for any other use. Use only recommended accessories.
1. Do not operate machine:
– Unless trained and authorized.                          – Unless you have read and 

– In flammable or explosive areas.                          understood the operator's manual.

– With a damaged cord or plug    

            – With the use of extension cords.

– If not in proper operating condition.                  – In outdoor areas and standing water.

2. Before operating machine:
– Make sure all safety devices are in place and operating properly.

3. When using machine:
– Do not run machine over cord.                        – Do not pull machine by cord or plug.
– Do not pull cord around                                   – Do not unplug by pulling on the cord.
   sharp edges or corners.                                   – Do not stretch cord.
– Do not handle plug with wet hands.                 – Keep cord away from heated surfaces.
– Report machine damage or fault 
   operation immediately.

To avoid electrical shock,please replace the power cord immediately if  any 
damage is being detected. The replacement must be performed only by an 
authorized person or by our customer service center. 

4. Before leaving or servicing machine:
– Turn off machine.                                               – Unplug cord from outlet.

5. When servicing machine:
– Unplug cord from outlet.                                  – Use manufacturer supplied or
                                                                               approved replacement parts.

Flammable materials can cause explosion or fire.  Do not use flammable 
materials in tanks or pick them up.

OPERATOR  MANUAL

ICE i18B/i18C

  

 5

FOR i18C

Содержание I18B


































Отзывы: