background image

OPERATOR  MANUAL

ICE i18B/i18C

   

8

MACHINE OPERATION

Do not operate machine unless you have read and understand this manual.

1) Lower squeegee assembly to the floor by spin the squeegee lifting handle(13).

2) Turn brush motor switch(20) to “on” position. 
3) Turn vacuum motor switch(21) to “on” position. 
4) Rotate the ball valve(12) handle to vertical position. Solution will not begin to flow until the        
    operating triggers (9) are pulled. 
5)  To  begin  scrubbing,  pull  on  the  blue  operating  trigger(9),  when  this  triggers  is  pulled,  the  pad                       

    driver  will begin to spin and the solution will begin to flow. 

6) Begin scrubbing by moving the machine forward

Do not keep the machine in the same position with the pad / brush spinning, 
or you might damage the floor.

7) Adjust solution flow by adjusting the position of ball valve knob.

WHILE OPERATING MACHINE

1) Occasionally open the cover tank(3) to see if there is any foam build-up.  If excessive foam is  
     found, add defoamer to the recovery tank.

Foam must not enter the float shut-off screen, or damage can occur to the 
vacuum motor. Foam will not activate the machine's float shut-off device.

2) Occasionally view the clear tube at the back left of the machine to check the amount of cleaning  
     solution that is left in the machine.

If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the 

blades down with a damp cloth.

Do not use your fingers to wipe or remove debris from the blades, as injury 
may occur.

When the solution tank runs empty, turn off the brush switch and ball valve of solution tank.  Keep 
the squeegee down and continue to vacuum until all the dirty water is picked up.

TANK DRAINING

1) Turn the switches on the control panel to “off ” position.
2) Raise the squeegee, transport machine to approved area for draining tank(s).

Any time scrubbing is completed, or when refilling solution tank, the 
recovery tank should be drained and cleaned.

If the recovery tank is not drained when the solution tank has been refilled, 
foam or water may enter the float shut-off mechanism and cause damage to 
the vacuum motor. 

Содержание I18B


































Отзывы: