ICE COBOTICS Cobi 18 Скачать руководство пользователя страница 47

Страница: 47 / 53

Autonomous Hard Floor Scrubber Cobi 18

User Manual

Battery & On Board Battery Charger

Cobi 18 has an on board Lithium Ion Battery and battery charger. Do not remove the battery or charger unless
authorized to do so.

Battery

Battery Charger

Nominal Voltage

25VDC

Nominal Capacity

25Ah

Allowed Max Charging Current

15A

Charging Temperature

0-45°C (32-113°F) /5~95%RH

Discharge Temperature

20-55°C (68-131°F) /5~95%RH

Storage Temperature

-10-30°C (14-86°F)

1. Only use the specific battery provided with Cobi 18. Do not

remove the battery unless authorized.

2. Battery power button must be turned on while machine is

charging or while machine is in use.

3. If machine is not being used for a long time, periodic charging

may be necessary.

4. Always keep the battery door open for ventilation when charging.

Input Voltage

100 -240 Vac 50/60 Hz

Output Voltage

24VDC

Charging Current

Temperature & Humidity

0-40°C (32-104°F) /20~55%RH

LED : GREEN ON

Wait for Charging / Fully charged

LED : YELLOW FLASH

Charging in progress

LED : RED FLASH

Charging Error

1. Only use the specific battery charger that Cobi 18 was delivered

with. Do not remove the battery charger unless authorized to do

so.

2. Always keep the battery door open for ventilation when charging.

3. Connect the AC power cable to approved power supply. A clear

window to the right of the battery door will allow visibility to the

charging status. Yellow will flash when battery is charging.

4. When the LED turns to Green, the battery is fully charged,

unplug the AC power cord and store it on the back of battery

compartment door.

5. If the LED light is flashing red, there is a charging error. Please

ensure the power cord is plugged into an approved outlet and

the battery power button is "on".

6. Please contact ICE Cobotics customer service if issue continues

to exist.

Содержание Cobi 18






















































Результаты поиска

Содержание Cobi 18

Отзывы:

Похожие инструкции для Cobi 18

Бренды по названию

Популярные бренды

ICE COBOTICS Cobi 18, Руководство пользователя

Результаты поиска

Содержание Cobi 18

Отзывы:

Похожие инструкции для Cobi 18

Бренды по названию

Популярные бренды