manualshive.com logo in svg

ICE COBOTICS Cobi 18, Руководство пользователя, Страница: 31 / 53

Поделиться
Скачать
ICE COBOTICS Cobi 18 Скачать руководство пользователя страница 31

31

Autonomous Hard Floor Scrubber Cobi 18

User Manual

Machine Operation in Autonomous Mode

Working in Autonomous Mode

4.  Push the corresponding icon to select the Cleaning Route(s) you want to clean, then touch on the icon [√] to 

confirm your selection and enter the Cleaning mode selection interface.

5.  There are three possible cleaning modes when in Autonomous mode.  Select the mode you want and push 

/ tap the corresponding icon.  Select the number of times you want to run the route and then push / tap the 
check mark to confirm your selection.

6.  Lock the handle and push the GO/STOP button according to the animation on the screen.  The vacuum and 

brush motors will turn on and the machine will begin to work in Autonomous mode.

ECO Mode: 

The machine will work in energy-saving mode. It 
is applicable for lighter duty scrubbing or when 
cleaning in a noise sensitive environment.

Max Mode:

 

The machine will work at full power, it is applicable 
for scrubbing heavily soiled floors.

Mop only Mode

Only the drive motors will be operational and the 
mop will pick up pre-existing moisture on the floor.

Содержание Cobi 18






















































Отзывы:

Нет отзывов