background image

Due to ICE AIR’s ongoing product development programs, the information in this document is subject to change without notice.

8

Indoor Air Filter

It is recommended that you clean the indoor 
air filter after every 350 to 400 hours of 
unit operation – more frequently if the unit 
is running in an environment of high dust, 
pet dander or other pollutants in the indoor 
atmosphere. 

Filter Replacement

Two filters are available for the ICE AIR units.

Reusable Filters can be removed at any 
point during the ICE AIR unit’s longevity. 
The Reusable Filter can be washed using a 
moderate hose and returned into the unit. 
The filter should be cleaned twice every 
year, before the start of every heating or 
cooling season. If damage occurs, the 
Reusable Filter should be replaced. Please 
contact your local sales representative for 
replacements.

Dispensable Filters should be replaced twice 
every year, before the start of every heating 
or cooling season. Please contact your local 
sales representative for replacements.

Maintenance

Your Ice Air unit is designed to provide many years of efficient, trouble-free comfort conditioning service. To ensure equipment longevity and 
efficiency, please make sure that the following simple maintenance procedures are followed. This manual assumes that your unit has been 
installed by a qualified installation professional, and is operating properly prior to maintenance service.

Have your unit periodically inspected by a properly trained service professional or building maintenance staff person. The unit should be 
checked for the safe and proper functioning of all of its systems at least once a year. The following recommended maintenance procedures 
should be carried out only by trained personnel with strict adherence to the Safety Guidelines outlined at the beginning of this manual. These 
procedures MUST be followed to ensure your safety and the safety of the person maintaining the equipment!

Condensate Drain Pan and Drain Hoses

Check the unit condensate drain pan and 
drain hoses annually to ensure proper 
condensate drainage. If any foreign matter 
build-up in the drain pan is found, clean the 
drain pan and drain hoses – frequency of 
cleaning depends on the level of dirt and 
pollutants that may be present in the indoor 
environment.

Evaporator Coil

Check and clean (if necessary) the unit 
evaporator coil annually.

Evaporator Motor and Blower Assembly 

Check and clean for dust and dirt build up as 
necessary. 

Compressor

Annual check should be performed to detect 
potential problems.

Condenser (Water Heat Exchanger)

Water coil maintenance is not required. If the 
unit installation is located in a system with 
water problem history, it is best to establish 
a periodic maintenance program. It is the 
building’s responsibility to maintain a water 
system that should provide your unit with 
treated and filtered water to keep water 
flowing freely through your equipment.

With these simple maintenance procedures 
carried out on a proper maintenance 
schedule, your unit should provide many 
years of trouble-free service. The procedures 
are covered in greater detail on the following 
pages and should be implemented by trained 
personnel. But there are certain items that 
you, the apartment owner or tenant, can do 
to ensure proper unit function:

•   Keep the area around your unit clear of 

objects that may block air flow into the 
unit – furniture, carpets and rugs, etc. 
may restrict air movement.

•   Keep the top of your cabinet free of 

objects that may block air flow out of the 
unit – plants, paperwork and books, etc. 
should not be placed on or above the 
discharge grille area.

•   Keep drapes, blinds and other window 

treatments clear of the air discharge 
area – any blockage of discharge air will 
have a negative impact on the unit and 
on its ability to properly condition the 
room.

General Unit Inspection

Visually inspect unit at least once a month. 
Pay special attention to hose assemblies and 
connections. Repair any leaks and replace 
deteriorated hose immediately to avoid 
potential costly damage to your property due 
to component failure.

REUSABLE FILTER

DISPENSIBLE FILTER

Содержание 5CHPW09

















Отзывы: