background image

EXCEL Canada

 

31 

Owner’s Manual 

 

LIMITED LIFETIME WARRANTY 

ICC EXCEL RESIDENTIAL CHIMNEY 

 
ICC  warrants  its  EXCEL  stainless  steel  chimney  lengths  to  be  free  from 
functional failure due to defects in material or workmanship for as long as 
the  original  consumer  owns  the  chimney  system.  This  warranty  provides 
for replacement of any chimney lengths which fail as a result of normal use 
on  a  residential  fireplace,  wood  burning  stove,  furnace  or  boiler  and 
includes replacement of any lengths damaged as a result of a chimney fire. 
(Note:  Chimney  fires  are  dangerous  and  preventable,  we  strongly 
encourage  you  to  have  your  chimney  cleaned  regularly).  This  warranty 
does not cover damage caused to the building by chimney fires or misuse 
of the product.   

No claims under this warranty will be honoured unless ICC is notified of the 
potential  claim  and  is  given  the  opportunity  to  have  one  of  its  agents 
examine the chimney prior to replacement.   

ICC  will  only  be  responsible  for  repair  or  replacement  of  any  chimney 
lengths found to be defective under this warranty. In no event shall ICC be 
responsible for any incidental or consequential damage caused by defects 
in the EXCEL chimney system.   

During  the  first  ten  years  of  the  warranty  ICC  will  provide  replacement 
chimney lengths at no charge. During the balance of the warranty ICC will 
provide replacement chimney lengths at 50% of the current retail price at 
the time of the warranty claim.   

ICC will not be responsible for labour of any kind required in the removal or 
replacement of an EXCEL system replaced under this warranty.   

This  chimney  is  designed  to  vent  residential  heating  oil,  untreated  wood, 
low  sulphur  coal,  and  natural  or  LP  gas.  It  is  designed  to  operate  at  a 
continuous  temperature  of  650°C  or  less.  It  is  not  designed  to  vent 
condensing  oil  or  gas  appliances.  This  warranty  is  void  if  the  chimney  is 
used in an application for which it is not designed.   

The  EXCEL  system  must  be  installed  according  to  the  Installation 
Instructions included with every system at the time of purchase. If you do 
not  have  a  set  of  installation  instructions  they  are  available  free  upon 
request.  This  warranty  is  void  if  the  chimney  is  not  installed  according  to 
the installation instructions.   

This  warranty  may  not  be  extended  or  modified  by  our  agents  or 
representatives. This warranty  is in lieu of all  other express warranties or 
guarantees, of any kind. 

 

Содержание EXCEL

































Отзывы: