background image

EXCEL Canada

 

20 

Owner’s Manual 

WALL SUPPORT (EWS) 

1. 

Assemble the band following the instructions on page 14.   

2. 

Fasten the wall support components to the band - see diagram above. 
The components are attached to the two elevator bolts projecting from 
the sides of the band.   

 

 

WALL RADIATION SHIELD (EWRS) 

If  you  are  installing  your  chimney  in  an  energy  efficient  house  which  has 
sealed  vapour  barriers  (e.g.:  R2000  construction)  we  manufacture  a 
special  wall  radiation  shield  so  that  you  can  maintain  your  vapour  barrier 
integrity. (See part EWRSI.)   

If possible install an interior chimney as it will provide better performance 
than  an  exterior  chimney.  In  area  with  continuous  temperatures  below 
-18°C  (0°  F)  the  use  of  an  exterior  chimney  may  result  in  operating 
problems  such  as  poor  draft,  excessive  condensation  of  combustion 
products  and  rapid  accumulation  of  creosote  when  connected  to  a  wood 
burning  appliance.  If  you  do  install  an  exterior  chimney,  we  recommend 
that you enclose it using an insulated enclosure.   

NOTES: 

 

1. 

The  chimney  may  be  enclosed  or  un-enclosed.  Always  maintain  2" 
clearance  to  combustible  materials.  Do  not  fill  the  space  around  the 
chimney with insulation or any other material.   

2. 

A  wall  support  must  be  used  to  secure  the  chimney  to  the  wall. 
Maximum distance between wall supports is 8 feet if the chimney is not 
enclosed.   

3. 

The chimney must extend in to the room at least 4 inches.   

Содержание EXCEL

































Отзывы: