IC Realtime 18G-16POE-Manage Скачать руководство пользователя

Страница: 5 / 34

User’s Guide

Page 5 of 34

Part One Hardware Installation Guide

Chapter 1 Product Instruction

1.1 Introduction

26G-24POE-Manage: 24*10/100/1000M

PoE ports,2*1000 Base-X SFP;1*Console port.

18G-16POE-Manage: 16*10/100/1000M

PoE ports,2*1000 Base-X SFP;1*Console port.

Switches.

1.2 Front Panel

1. 26G-24POE-Manage

24*10/100/1000M

PoE ports,2*1000 Base-X SFP;1*Console port .

Picture 1.2.1 26G-24POE-Manage: Front Panel

2. 18G-16POE-Manage

16*10/100/1000M

PoE ports,2*1000 Base-X SFP;1*Console port .

Picture 1.2.1 18G-16POE-Manage Front Panel

LED Indicator Instruction

Please check the LED indicators on the left of front panel.

1. System Indicator

The system indicator is on the upper-left side of front panel, indicator, the indicator is on when

switch works normally.

2. Power Indicator

Below the system indicator is the power indicator, it is on if the switch is powered on.If the

indicator is off, please check the power supply.

3. 10/100Mbps Link/ACT Indicators

Содержание 18G-16POE-Manage



































Результаты поиска

Содержание 18G-16POE-Manage

Отзывы:

Похожие инструкции для 18G-16POE-Manage

Бренды по названию

Популярные бренды

IC Realtime 18G-16POE-Manage, Руководство пользователя

Результаты поиска

Содержание 18G-16POE-Manage

Отзывы:

Похожие инструкции для 18G-16POE-Manage

Бренды по названию

Популярные бренды