IBP HDM97 Pocket Series Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 50

background image

SAFETY INSTRUCTIONS

For your and your patients safety read and consider the safety instructions below carefully

•

Read the entire manual carefully before using the HDM97Pocket.

•

Keep the instrument away from unauthorised persons.

•

Only use the

HDM97

Pocket as reference instrument to measure Conductivity, Temperature,

Pressure, Flow and pH depending to it's equipped features.

•

Never use the HDM97Pocket as a replacement of sensors of a medical device.

•

Do not use the HDM97Pocket in conjunction with a medical device during a treatment.

•

Only use the instrument in a dry environment and do not touch it with wet hands.

•

Make sure that no liquids intrude inside the instrument or it's inlets / outlets.

•

Always use a clean protection filter for the pressure transducer inlet.

•

Prevent every mechanical overstraining of electrical wires. Never buckle or pull the cable of the
conductivity probe.

•

If the acquired values seem to be not believable, make sure that the

HDM97

Pocket is not defective

•

Prevent electrostatic discharge on the connectors. This can lead to substantial damage of the
instrument. Make sure to be completely discharged before touching the connectors or cables
connected to the instrument.

•

Adjust the meter only, if you are familiar with the consequences of the adjustment. Consider the
hints for reference solutions in the user manual.

•

Potentials above 42V against earth ground are dangerous. This potentials can lead to electrical
shock and therefore to health hazards. Make sure that none of the connectors has higher voltage
than mentioned before.

•

The direct connection of earth potential to any connector of the instrument is not applicable for
safety purposes and may substantially damage the instrument. Make sure that the medical device
itself is properly connected to earth ground according to its instruction manual.

•

Make sure that the instrument never heats over 60°C / 140°F. Prevent direct sunlight.

•

Never sterilize the instrument using an autoclave. Danger of explosion of the battery!

•

Never throw the meter into a fire. Danger of explosion of the battery!

•

Never open the meter. There are no parts inside you can repair.

•

Never try to replace or repair the internal battery. Handled in the wrong way these part is
dangerous. Extreme risk of fire and explosion!

«
1
2
3
4
5
...
»

Содержание HDM97 Pocket Series



















































Отзывы:

Нет отзывов

Похожие инструкции для HDM97 Pocket Series

Бренд: Kawai Страницы: 33

Бренд: Kawai Страницы: 60

Бренд: Omega Engineering Страницы: 22

Бренд: Daewoo Страницы: 2

Surface Scatter 7 sc

Бренд: Hach Страницы: 6

Бренд: Hach Страницы: 118

Бренд: Hach Страницы: 388

Orbisphere 51 Series

Бренд: Hach Страницы: 118

ORBISPHERE 3650 Atex

Бренд: Hach Страницы: 51

Бренд: Hach Страницы: 72

POLYMETRON 8362

Бренд: Hach Страницы: 78

Pocket Colorimeter II

Бренд: HACH LANGE Страницы: 146

Бренд: Hach Страницы: 146

Бренд: Hach Страницы: 36

PHOSPHAX indoor sc

Бренд: Hach Страницы: 104

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 384

Бренд: Hach Страницы: 172

Бренд: Weller Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды